Internet Engineering Task Force L. Avramov Internet-Draft, Intended status: Informational Cisco Systems Expires: October 29, 2016 J. Rapp April 27, 2016 VMware Data Center Benchmarking Terminology draft-ietf-bmwg-dcbench-terminology-05 Abstract The purpose of this informational document is to establish definitions, discussion and measurement techniques for data center benchmarking. Also, it is to introduce new terminologies applicable to data center performance evaluations. The purpose of this document is not to define the test methodology, but rather establish the important concepts when one is interested in benchmarking network switches and routers in the data center. Status of this Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet-Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http://www.ietf.org/1id-abstracts.html The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html Copyright Notice Copyright (c) 2013 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in Avramov & Rapp Expires October 29, 2016 [Page 1] Internet-Draft Data Center Benchmarking Terminology April 27, 2016 effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.1. Requirements Language . . . . . . . . . . . . . . . . . . 4 1.2. Definition format . . . . . . . . . . . . . . . . . . . . . 4 2. Latency . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2.1. Definition . . . . . . . . . . . . . . . . . . . . . . . . 4 2.2 Discussion . . . . . . . . . . . . . . . . . . . . . . . . . 5 2.3 Measurement Units . . . . . . . . . . . . . . . . . . . . . 6 3 Jitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3.1 Definition . . . . . . . . . . . . . . . . . . . . . . . . . 6 3.2 Discussion . . . . . . . . . . . . . . . . . . . . . . . . . 6 3.3 Measurement Units . . . . . . . . . . . . . . . . . . . . . 6 4 Physical Layer Calibration . . . . . . . . . . . . . . . . . . . 7 4.1 Definition . . . . . . . . . . . . . . . . . . . . . . . . . 7 4.2 Discussion . . . . . . . . . . . . . . . . . . . . . . . . . 7 4.3 Measurement Units . . . . . . . . . . . . . . . . . . . . . 7 5 Line rate . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 5.1 Definition . . . . . . . . . . . . . . . . . . . . . . . . . 8 5.2 Discussion . . . . . . . . . . . . . . . . . . . . . . . . . 8 5.3 Measurement Units . . . . . . . . . . . . . . . . . . . . . 9 6 Buffering . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 6.1 Buffer . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 6.1.1 Definition . . . . . . . . . . . . . . . . . . . . . . . 10 6.1.2 Discussion . . . . . . . . . . . . . . . . . . . . . . . 12 6.1.3 Measurement Units . . . . . . . . . . . . . . . . . . . 12 6.2 Incast . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 6.2.1 Definition . . . . . . . . . . . . . . . . . . . . . . . 12 6.2.2 Discussion . . . . . . . . . . . . . . . . . . . . . . . 13 6.2.3 Measurement Units . . . . . . . . . . . . . . . . . . . 13 7 Application Throughput: Data Center Goodput . . . . . . . . . . 13 7.1. Definition . . . . . . . . . . . . . . . . . . . . . . . . 13 7.2. Discussion . . . . . . . . . . . . . . . . . . . . . . . . 14 7.3. Measurement Units . . . . . . . . . . . . . . . . . . . . . 14 8. References . . . . . . . . . . . . . . . . . . . . . . . . . . 15 3.1. Normative References . . . . . . . . . . . . . . . . . . . 15 3.2. Informative References . . . . . . . . . . . . . . . . . . 15 3.3. URL References . . . . . . . . . . . . . . . . . . . . . . 15 3.4. Acknowledgments . . . . . . . . . . . . . . . . . . . . . 15 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 15 Avramov & Rapp Expires October 29, 2016 [Page 2] Internet-Draft Data Center Benchmarking Terminology April 27, 2016 1. Introduction Traffic patterns in the data center are not uniform and are contently changing. They are dictated by the nature and variety of applications utilized in the data center. It can be largely east-west traffic flows in one data center and north-south in another, while some may combine both. Traffic patterns can be bursty in nature and contain many-to-one, many-to-many, or one-to-many flows. Each flow may also be small and latency sensitive or large and throughput sensitive while containing a mix of UDP and TCP traffic. All of which can coexist in a single cluster and flow through a single network device all at the same time. Benchmarking of network devices have long used RFC1242, RFC2432, RFC2544, RFC2889 and RFC3918. These benchmarks have largely been focused around various latency attributes and max throughput of the Device Under Test being benchmarked. These standards are good at measuring theoretical max throughput, forwarding rates and latency under testing conditions, but to not represent real traffic patterns that may affect these networking devices. The data center networking devices covered are switches and routers. The following defines a set of definitions, metrics and terminologies including congestion scenarios, switch buffer analysis and redefines basic definitions in order to represent a wide mix of traffic conditions. Avramov & Rapp Expires October 29, 2016 [Page 3] Internet-Draft Data Center Benchmarking Terminology April 27, 2016 1.1. Requirements Language The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119 [6]. 1.2. Definition format Term to be defined. (e.g., Latency) Definition: The specific definition for the term. Discussion: A brief discussion about the term, it's application and any restrictions on measurement procedures. Measurement Units: Methodology for the measure and units used to report measurements of this term, if applicable. 2. Latency 2.1. Definition Latency is a the amount of time it takes a frame to transit the DUT. Latency is measured in unit of time (seconds, milliseconds, microseconds and so on). The purpose of measuring latency is to understand what is the impact of adding a device in the communication path. The Latency interval can be assessed between different combinations of events, irrespectively of the type of switching device (bit forwarding aka cut-through or store forward type of device) Traditionally the latency measurement definitions are: FILO (First In Last Out) The time interval starting when the end of the first bit of the input frame reaches the input port and ending when the last bit of the output frame is seen on the output port FIFO (First In First Out) The time interval starting when the end of the first bit of the input frame reaches the input port and ending when the start of the first bit of the output frame is seen on the output port LILO (Last In Last Out) The time interval starting when the last bit of the input frame reaches the input port and the last bit of the Avramov & Rapp Expires October 29, 2016 [Page 4] Internet-Draft Data Center Benchmarking Terminology April 27, 2016 output frame is seen on the output port LIFO (Last In First Out) The time interval starting when the last bit of the input frame reaches the input port and ending when the first bit of the output frame is seen on the output port. Another possibility to summarize the four different definitions above is to refer to the bit position as they normally occur: input to output. FILO is FL (First bit Last bit) FIFO is FF (First bit First bit) LILO is LL (Last bit Last bit) LIFO is LF (Last bit First bit) This definition explained in this section in context of data center switching benchmarking is in lieu of the previous definition of Latency defined in RFC 1242, section 3.8 and is quoted here: For store and forward devices: The time interval starting when the last bit of the input frame reaches the input port and ending when the first bit of the output frame is seen on the output port. For bit forwarding devices: The time interval starting when the end of the first bit of the input frame reaches the input port and ending when the start of the first bit of the output frame is seen on the output port. 2.2 Discussion FILO is the most important measuring definition. Any type of switches MUST be measured with the FILO mechanism: FILO will include the latency of the switch and the latency of the frame as well as the serialization delay. It is a picture of the 'whole' latency going through the DUT. For applications, which are latency sensitive and can function with initial bytes of the frame, FIFO MAY be an additional type of measuring to supplement FILO. Not all DUTs are exclusively cut-through or store-and-forward. Data Center DUTs are frequently store-and-forward for smaller packet sizes and then adopting a cut-through behavior. FILO covers all scenarios. LIFO mechanism can be used with store forward type of switches but not with cut-through type of switches, as it will provide negative latency values for larger packet sizes because LIFO removes the serialization delay. Therefore, this mechanism MUST NOT be used when comparing latencies of two different DUTs. Avramov & Rapp Expires October 29, 2016 [Page 5] Internet-Draft Data Center Benchmarking Terminology April 27, 2016 2.3 Measurement Units The measuring methods to use for benchmarking purposes are as follow: 1) FILO MUST be used as a measuring method, as this will include the latency of the packet; and today the application commonly need to read the whole packet to process the information and take an action. 2) FIFO MAY be used for certain applications able to proceed data as the first bits arrive (FPGA for example) 3) LIFO MUST not be used, because it subtracts the latency of the packet; unlike all the other methods. 3 Jitter 3.1 Definition Jitter in the data center context is synonymous with the common term Delay variation. It is derived from multiple measurements of one-way delay, as described in RFC 3393. The mandatory definition of Delay Variation is the PDV form from section 4.2 of RFC 5481. When considering a stream of packets, the delays of all packets are subtracted from the minimum delay over all packets in the stream. This facilitates assessment of the range of delay variation (Max - Min), or a high percentile of PDV (99th percentile, for robustness against outliers). If First-bit to Last-bit timestamps are used for Delay measurement, then Delay Variation MUST be measured using packets or frames of the same size, since the definition of latency includes the serialization time for each packet. Otherwise if using First-bit to First-bit, the size restriction does not apply. 3.2 Discussion In addition to PDV Range and or a high percentile of PDV, Inter- Packet Delay Variation (IPDV) as defined in section 4.1 of RFC5481 (differences between two consecutive packets) MAY be used for the purpose of determining how packet spacing has changed during transfer, for example to see if packet stream has become closely- spaced or "bursty". However, the Absolute Value of IPDV SHOULD NOT be used, as this collapses the "bursty" and "dispersed" sides of the IPDV distribution together. 3.3 Measurement Units Avramov & Rapp Expires October 29, 2016 [Page 6] Internet-Draft Data Center Benchmarking Terminology April 27, 2016 The measurement of delay variation is expressed in units of seconds. A PDV histogram MAY be provided for the population of packets measured. 4 Physical Layer Calibration 4.1 Definition The calibration of the physical layer consists of defining and measuring the latency of the physical devices used to perform test on the DUT. It includes the list of all physical layer components used as listed here after: -type of device used to generate traffic / measure traffic -type of line cards used on the traffic generator -type of transceivers on traffic generator -type of transceivers on DUT -type of cables -length of cables -software name, and version of traffic generator and DUT -list of enabled features on DUT MAY be provided and is recommended [especially the control plane protocols such as LLDP, Spanning-Tree etc.]. A comprehensive configuration file MAY be provided to this effect. 4.2 Discussion Physical layer calibration is part of the end to end latency, which should be taken into acknowledgment while evaluating the DUT. Small variations of the physical components of the test may impact the latency being measure so they MUST be described when presenting results. 4.3 Measurement Units It is RECOMMENDED to use all cables of : the same type, the same Avramov & Rapp Expires October 29, 2016 [Page 7] Internet-Draft Data Center Benchmarking Terminology April 27, 2016 length, when possible using the same vendor. It is a MUST to document the cables specifications on section [4.1s] along with the test results. The test report MUST specify if the cable latency has been removed from the test measures or not. The accuracy of the traffic generator measure MUST be provided [this is usually a value in the 20ns range for current test equipment]. 5 Line rate 5.1 Definition The transmit timing, or maximum transmitted data rate is controlled by the "transmit clock" in the DUT. The receive timing (maximum ingress data rate) is derived from the transmit clock of the connected interface. The line rate or physical layer frame rate is the maximum capacity to send frames of a specific size at the transmit clock frequency of the DUT. The term port capacity term defines the maximum speed capability for the given port; for example 1GE, 10GE, 40GE, 100GE etc. The frequency ("clock rate") of the transmit clock in any two connected interfaces will never be precisely the same, therefore a tolerance is needed, this will be expressed by Parts Per Million (PPM) value. The IEEE standards allow a specific +/- variance in the transmit clock rate, and Ethernet is designed to allow for small, normal variations between the two clock rates. This results in a tolerance of the line rate value when traffic is generated from a testing equipment to a DUT. Line rate SHOULD be measured in frames per second. 5.2 Discussion For a transmit clock source, most Ethernet switches use "clock modules" (also called "oscillator modules") that are sealed, internally temperature-compensated, and very accurate. The output frequency of these modules is not adjustable because it is not necessary. Many test sets, however, offer a software-controlled adjustment of the transmit clock rate, which should be used to compensate the test equipment to not send more than line rate of the DUT. To allow for the minor variations typically found in the clock rate of commercially-available clock modules and other crystal-based Avramov & Rapp Expires October 29, 2016 [Page 8] Internet-Draft Data Center Benchmarking Terminology April 27, 2016 oscillators, Ethernet standards specify the maximum transmit clock rate variation to be not more than +/- 100 PPM (parts per million) from a calculated center frequency. Therefore a DUT must be able to accept frames at a rate within +/- 100 PPM to comply with the standards. Very few clock circuits are precisely +/- 0.0 PPM because: 1.The Ethernet standards allow a maximum of +/- 100 PPM (parts per million) variance over time. Therefore it is normal for the frequency of the oscillator circuits to experience variation over time and over a wide temperature range, among external factors. 2.The crystals or clock modules, usually have a specific +/- PPM variance that is significantly better than +/- 100 PPM. Often times this is +/- 30 PPM or better in order to be considered a "certification instrument". When testing an Ethernet switch throughput at "line rate", any specific switch will have a clock rate variance. If a test set is running +1 PPM faster than a switch under test, and a sustained line rate test is performed, a gradual increase in latency and eventually packet drops as buffers fill and overflow in the switch can be observed. Depending on how much clock variance there is between the two connected systems, the effect may be seen after the traffic stream has been running for a few hundred microseconds, a few milliseconds, or seconds. The same low latency and no-packet-loss can be demonstrated by setting the test set link occupancy to slightly less than 100 percent link occupancy. Typically 99 percent link occupancy produces excellent low-latency and no packet loss. No Ethernet switch or router will have a transmit clock rate of exactly +/- 0.0 PPM. Very few (if any) test sets have a clock rate that is precisely +/- 0.0 PPM. Test set equipment manufacturers are well-aware of the standards, and allows a software-controlled +/- 100 PPM "offset" (clock-rate adjustment) to compensate for normal variations in the clock speed of "devices under test". This offset adjustment allows engineers to determine the approximate speed the connected device is operating, and verify that it is within parameters allowed by standards. 5.3 Measurement Units "Line Rate" CAN be measured in terms of "Frame Rate": Frame Rate = Transmit-Clock-Frequency / (Frame-Length*8 + Minimum_Gap Avramov & Rapp Expires October 29, 2016 [Page 9] Internet-Draft Data Center Benchmarking Terminology April 27, 2016 + Preamble + Start-Frame Delimiter) Minimum_Gap represents the inter frame gap. This formula "scales up" or "scales down" to represent 1 GB Ethernet, or 10 GB Ethernet and so on. Example for 1 GB Ethernet speed with 64-byte frames: Frame Rate = 1,000,000,000 /(64*8 + 96 + 56 + 8) Frame Rate = 1,000,000,000 / 672 Frame Rate = 1,488,095.2 frames per second. Considering the allowance of +/- 100 PPM, a switch may "legally" transmit traffic at a frame rate between 1,487,946.4 FPS and 1,488,244 FPS. Each 1 PPM variation in clock rate will translate to a 1.488 frame-per-second frame rate increase or decrease. In a production network, it is very unlikely to see precise line rate over a very brief period. There is no observable difference between dropping packets at 99% of line rate and 100% of line rate. -Line rate CAN measured at 100% of line rate with a -100PPM adjustment. - Line rate SHOULD be measured at 99,98% with 0 PPM adjustment.-The PPM adjustment SHOULD only be used for a line rate type of measurement 6 Buffering 6.1 Buffer 6.1.1 Definition Buffer Size: the term buffer size, represents the total amount of frame buffering memory available on a DUT. This size is expressed in Byte; KB (kilobytes), MB (megabytes) or GB (gigabyte). When the buffer size is expressed it SHOULD be defined by a size metric defined above. When the buffer size is expressed, an indication of the frame MTU used for that measurement is also necessary as well as the cos or dscp value set; as often times the buffers are carved by quality of service implementation. (please refer to the buffer efficiency section for further details). Example: Buffer Size of DUT when sending 1518 bytes frames is 18 Mb. Port Buffer Size: the port buffer size is the amount of buffer a single ingress port, egress port or combination of ingress and egress buffering location for a single port. The reason of mentioning the three locations for the port buffer is, that the DUT buffering scheme can be unknown or untested, and therefore the indication of where the buffer is located helps understand the buffer architecture and therefore the total buffer size. The Port Buffer Size is an Avramov & Rapp Expires October 29, 2016 [Page 10] Internet-Draft Data Center Benchmarking Terminology April 27, 2016 informational value that MAY be provided from the DUT vendor. It is not a value that is tested by benchmarking. Benchmarking will be done using the Maximum Port Buffer Size or Maximum Buffer Size methodology. Maximum Port Buffer Size: this is in most cases the same as the Port Buffer Size. In certain switch architecture called SoC (switch on chip), there is a concept of port buffer and shared buffer pool available for all ports. Maximum Port Buffer, defines the scenario of a SoC buffer, where this amount in B (byte), KB (kilobyte), MB (megabyte) or GB (gigabyte) would represent the sum of the port buffer along with the maximum value of shared buffer this given port can take. The Maximum Port Buffer Size needs to be expressed along with the frame MTU used for the measurement and the cos or dscp bit value set for the test. Example: a DUT has been measured to have 3KB of port buffer for 1518 frame size packets and a total of 4.7 MB of maximum port buffer for 1518 frame size packets and a cos of 0. Maximum DUT Buffer Size: this is the total size of Buffer a DUT can be measured to have. It is most likely different than the Maximum Port Buffer Size. It CAN also be different from the sum of Maximum Port Buffer Size. The Maximum Buffer Size needs to be expressed along with the frame MTU used for the measurement and along with the cos or dscp value set during the test. Example: a DUT has been measured to have 3KB of port buffer for 1518 frame size packets and a total of 4.7 MB of maximum port buffer for 1518 frame size packets. The DUT has a Maximum Buffer Size of 18 MB at 1500 bytes and a cos of 0. Burst: The burst is a fixed number of packets sent over a percentage of linerate of a defined port speed. The amount of frames sent are evenly distributed across the interval T. A constant C, can be defined to provide the average time between two consecutive packets evenly spaced. Microburst: it is a burst. A microburst is when packet drops occur when there is not sustained or noticeable congestion upon a link or device. A characterization of microburst is when the Burst is not evenly distributed over T, and is less than the constant C [C= average time between two consecutive packets evenly spaced out]. Intensity of Microburst: this is a percentage, representing the level of microburst between 1 and 100%. The higher the number the higher the microburst is. I=[1-[ (TP2-Tp1)+(Tp3-Tp2)+....(TpN-Tp(n-1) ] / Sum(packets)]]*100 Avramov & Rapp Expires October 29, 2016 [Page 11] Internet-Draft Data Center Benchmarking Terminology April 27, 2016 The above definitions are not meant to comment on the ideal sizing of a buffer, rather on how to measure it. A larger buffer is not necessarily better and CAN cause issues with buffer bloat. 6.1.2 Discussion When measuring buffering on a DUT, it is important to understand what the behavior is for each port, and also for all ports as this will provide an evidence of the total amount of buffering available on the switch. The terms of buffer efficiency here helps one understand what is the optimum packet size for the buffer to be used, or what is the real volume of buffer available for a specific packet size. This section does not discuss how to conduct the test methodology, it rather explains the buffer definitions and what metrics should be provided for a comprehensive data center device buffering benchmarking. 6.1.3 Measurement Units When Buffer is measured:-the buffer size MUST be measured-the port buffer size MAY be provided for each port-the maximum port buffer size MUST be measured-the maximum DUT buffer size MUST be measured- the intensity of microburst MAY be mentioned when a microburst test is performed-the cos or dscp value set during the test SHOULD be provided 6.2 Incast 6.2.1 Definition The term Incast, very commonly utilized in the data center, refers to the traffic pattern of many-to-one or many-to-many conversations. Typically in the data center it would refer to many different ingress server ports(many), sending traffic to a common uplink (one), or multiple uplinks (many). This pattern is generalized for any network as many incoming ports sending traffic to one or few uplinks. It can also be found in many-to-many traffic patterns. Synchronous arrival time: When two, or more, frames of respective sizes L1 and L2 arrive at their respective one or multiple ingress ports, and there is an overlap of the arrival time for any of the bits on the DUT, then the frames L1 and L2 have a synchronous arrival times. This is called incast. Asynchronous arrival time: Any condition not defined by synchronous. Percentage of synchronization: this defines the level of overlap Avramov & Rapp Expires October 29, 2016 [Page 12] Internet-Draft Data Center Benchmarking Terminology April 27, 2016 [amount of bits] between the frames L1,L2..Ln. Example: two 64 bytes frames, of length L1 and L2, arrive to ingress port 1 and port 2 of the DUT. There is an overlap of 6.4 bytes between the two where L1 and L2 were at the same time on the respective ingress ports. Therefore the percentage of synchronization is 10%. Stateful type traffic defines packets exchanged with a stateful protocol such as for example TCP. Stateless type traffic defines packets exchanged with a stateless protocol such as for example UDP. 6.2.2 Discussion In this scenario, buffers are solicited on the DUT. In a ingress buffering mechanism, the ingress port buffers would be solicited along with Virtual Output Queues, when available; whereas in an egress buffer mechanism, the egress buffer of the one outgoing port would be used. In either cases, regardless of where the buffer memory is located on the switch architecture; the Incast creates buffer utilization. When one or more frames having synchronous arrival times at the DUT they are considered forming an incast. 6.2.3 Measurement Units It is a MUST to measure the number of ingress and egress ports. It is a MUST to have a non null percentage of synchronization, which MUST be specified. 7 Application Throughput: Data Center Goodput 7.1. Definition In Data Center Networking, a balanced network is a function of maximal throughput 'and' minimal loss at any given time. This is defined by the Goodput. Goodput is the application-level throughput. The definition used is a variance of the definition in RFC 2647. Avramov & Rapp Expires October 29, 2016 [Page 13] Internet-Draft Data Center Benchmarking Terminology April 27, 2016 Goodput is the number of bits per unit of time forwarded to the correct destination interface of the DUT/SUT, minus any bits retransmitted. 7.2. Discussion In data center benchmarking, the goodput is a value that SHOULD be measured. It provides a realistic idea of the usage of the available bandwidth. A goal in data center environments is to maximize the goodput while minimizing the loss. 7.3. Measurement Units When S is the total bytes received from all senders [not inclusive of packet headers or TCP headers - it's the payload] and Ft is the Finishing Time of the last sender; the Goodput G is then measured by the following formula: G= S / Ft bytes per second Example: a TCP file transfer over HTTP protocol on a 10Gb/s media. The file cannot be transferred over Ethernet as a single continuous stream. It must be broken down into individual frames of 1500 bytes when the standard MTU [Maximum Transmission Unit] is used. Each packet requires 20 bytes of IP header information and 20 bytes of TCP header information, therefore 1460 byte are available per packet for the file transfer. Linux based systems are further limited to 1448 bytes as they also carry a 12 byte timestamp. Finally, the date is transmitted in this example over Ethernet which adds a 26 byte overhead per packet. G= 1460/1526 x 10 Gbit/s which is 9.567 Gbit/s or 1.196 Gigabytes per second. Please note: this example does not take into consideration additional Ethernet overhead, such as the interframe gap (a minimum of 96 bit times), nor collisions (which have a variable impact, depending on the network load). When conducting Goodput measurements please document in addition to the 4.1 section: -the TCP Stack used -OS Versions -NIC firmware version and model For example, Windows TCP stacks and different Linux versions can Avramov & Rapp Expires October 29, 2016 [Page 14] Internet-Draft Data Center Benchmarking Terminology April 27, 2016 influence TCP based tests results. 8. References 3.1. Normative References [1] Bradner, S. "Benchmarking Terminology for Network Interconnection Devices", RFC 1242, July 1991. [2] Bradner, S. and J. McQuaid, "Benchmarking Methodology for Network Interconnect Devices", RFC 2544, March 1999. 3.2. Informative References [3] Mandeville R. and Perser J., "Benchmarking Methodology for LAN Switching Devices", RFC 2889, August 2000. [4] Stopp D. and Hickman B., "Methodology for IP Multicast Benchmarking", BCP 26, RFC 3918, October 2004. 3.3. URL References [5] Yanpei Chen, Rean Griffith, Junda Liu, Randy H. Katz, Anthony D. Joseph, "Understanding TCP Incast Throughput Collapse in Datacenter Networks", http://www.eecs.berkeley.edu/~ychen2/professional/TCPIncastWREN2009.pdf". 3.4. Acknowledgments The authors would like to thank Alfred Morton, Scott Bradner, Ian Cox, Tim Stevenson for their reviews and feedback. Authors' Addresses Lucien Avramov Cisco Systems 170 West Tasman drive San Jose, CA 95134 United States Phone: +1 408 526 7686 Email: lavramov@cisco.com Jacob Rapp VMware 3401 Hillview Ave Avramov & Rapp Expires October 29, 2016 [Page 15] Internet-Draft Data Center Benchmarking Terminology April 27, 2016 Palo Alto, CA 94304 United States Phone: +1 650 857 3367 Email: jrapp@vmware.com Avramov & Rapp Expires October 29, 2016 [Page 16]