MPTCP Working Group O. Bonaventure Internet-Draft UCLouvain Intended status: Informational C. Paasch Expires: March 2, 2017 Apple, Inc. G. Detal Tessares August 29, 2016 Use Cases and Operational Experience with Multipath TCP draft-ietf-mptcp-experience-06 Abstract This document discusses both use cases and operational experience with Multipath TCP in real world networks. It lists several prominent use cases for which Multipath TCP has been considered and is being used. It also gives insight to some heuristics and decisions that have helped to realize these use cases. Status of this Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at http://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." This Internet-Draft will expire on March 2, 2017. Copyright Notice Copyright (c) 2016 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must Bonaventure, et al. Expires March 2, 2017 [Page 1] Internet-Draft MPTCP Experience August 2016 include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3 2. Use cases . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2.1. Datacenters . . . . . . . . . . . . . . . . . . . . . . . 5 2.2. Cellular/WiFi Offload . . . . . . . . . . . . . . . . . . 5 2.3. Multipath TCP proxies . . . . . . . . . . . . . . . . . . 9 3. Operational Experience . . . . . . . . . . . . . . . . . . . . 11 3.1. Middlebox interference . . . . . . . . . . . . . . . . . . 11 3.2. Congestion control . . . . . . . . . . . . . . . . . . . . 13 3.3. Subflow management . . . . . . . . . . . . . . . . . . . . 13 3.4. Implemented subflow managers . . . . . . . . . . . . . . . 14 3.5. Subflow destination port . . . . . . . . . . . . . . . . . 16 3.6. Closing subflows . . . . . . . . . . . . . . . . . . . . . 17 3.7. Packet schedulers . . . . . . . . . . . . . . . . . . . . 18 3.8. Segment size selection . . . . . . . . . . . . . . . . . . 19 3.9. Interactions with the Domain Name System . . . . . . . . . 19 3.10. Captive portals . . . . . . . . . . . . . . . . . . . . . 20 3.11. Stateless webservers . . . . . . . . . . . . . . . . . . . 21 3.12. Loadbalanced serverfarms . . . . . . . . . . . . . . . . . 22 4. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 23 5. Security Considerations . . . . . . . . . . . . . . . . . . . 24 6. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 25 7. Informative References . . . . . . . . . . . . . . . . . . . . 26 Appendix A. Changelog . . . . . . . . . . . . . . . . . . . . . . 33 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 35 Bonaventure, et al. Expires March 2, 2017 [Page 2] Internet-Draft MPTCP Experience August 2016 1. Introduction Multipath TCP was standardized in [RFC6824] and five independent implementations have been developed. As of September 2015, Multipath TCP has been or is being implemented on the following platforms: o Linux kernel [MultipathTCP-Linux] o Apple iOS and MacOS [Apple-MPTCP] o Citrix load balancers o FreeBSD [FreeBSD-MPTCP] o Oracle The first three implementations are known to interoperate. The last two are currently being tested and improved against the Linux implementation. Three of these implementations are open-source. Apple's implementation is widely deployed. Since the publication of [RFC6824], experience has been gathered by various network researchers and users about the operational issues that arise when Multipath TCP is used in today's Internet. When the MPTCP working group was created, several use cases for Multipath TCP were identified [RFC6182]. Since then, other use cases have been proposed and some have been tested and even deployed. We describe these use cases in Section 2. Section 3 focuses on the operational experience with Multipath TCP. Most of this experience comes from the utilisation of the Multipath TCP implementation in the Linux kernel [MultipathTCP-Linux]. This open-source implementation has been downloaded and is used by thousands of users all over the world. Many of these users have provided direct or indirect feedback by writing documents (scientific articles or blog messages) or posting to the mptcp-dev mailing list (see https://listes-2.sipr.ucl.ac.be/sympa/arc/mptcp-dev ). This Multipath TCP implementation is actively maintained and continuously improved. It is used on various types of hosts, ranging from smartphones or embedded routers to high-end servers. The Multipath TCP implementation in the Linux kernel is not, by far, the most widespread deployment of Multipath TCP. Since September 2013, Multipath TCP is also supported on smartphones and tablets running iOS7 [IOS7]. There are likely hundreds of millions of Multipath TCP enabled devices. However, this particular Multipath TCP implementation is currently only used to support a single Bonaventure, et al. Expires March 2, 2017 [Page 3] Internet-Draft MPTCP Experience August 2016 application. Unfortunately, there is no public information about the lessons learned from this large scale deployment. Section 3 is organized as follows. Supporting the middleboxes was one of the difficult issues in designing the Multipath TCP protocol. We explain in Section 3.1 which types of middleboxes the Linux Kernel implementation of Multipath TCP supports and how it reacts upon encountering these. Section 3.2 summarises the MPTCP specific congestion controls that have been implemented. Section 3.3 to Section 3.7 discuss heuristics and issues with respect to subflow management as well as the scheduling across the subflows. Section 3.8 explains some problems that occurred with subflows having different Maximum Segment Size (MSS) values. Section 3.9 presents issues with respect to content delivery networks and suggests a solution to this issue. Finally, Section 3.10 documents an issue with captive portals where MPTCP will behave suboptimally. Bonaventure, et al. Expires March 2, 2017 [Page 4] Internet-Draft MPTCP Experience August 2016 2. Use cases Multipath TCP has been tested in several use cases. There is already an abundant scientific literature on Multipath TCP [MPTCPBIB]. Several of the papers published in the scientific literature have identified possible improvements that are worth being discussed here. 2.1. Datacenters A first, although initially unexpected, documented use case for Multipath TCP has been in datacenters [HotNets][SIGCOMM11]. Today's datacenters are designed to provide several paths between single- homed servers. The multiplicity of these paths comes from the utilization of Equal Cost Multipath (ECMP) and other load balancing techniques inside the datacenter. Most of the deployed load balancing techniques in datacenters rely on hashes computed over the five tuple. Thus all packets from the same TCP connection follow the same path and so are not reordered. The results in [HotNets] demonstrate by simulations that Multipath TCP can achieve a better utilization of the available network by using multiple subflows for each Multipath TCP session. Although [RFC6182] assumes that at least one of the communicating hosts has several IP addresses, [HotNets] demonstrates that Multipath TCP is beneficial when both hosts are single-homed. This idea is analysed in more details in [SIGCOMM11] where the Multipath TCP implementation in the Linux kernel is modified to be able to use several subflows from the same IP address. Measurements in a public datacenter show the quantitative benefits of Multipath TCP [SIGCOMM11] in this environment. Although ECMP is widely used inside datacenters, this is not the only environment where there are different paths between a pair of hosts. ECMP and other load balancing techniques such as Link Aggregation Groups (LAG) are widely used in today's networks and having multiple paths between a pair of single-homed hosts is becoming the norm instead of the exception. Although these multiple paths have often the same cost (from an IGP metrics viewpoint), they do not necessarily have the same performance. For example, [IMC13c] reports the results of a long measurement study showing that load balanced Internet paths between that same pair of hosts can have huge delay differences. 2.2. Cellular/WiFi Offload A second use case that has been explored by several network researchers is the cellular/WiFi offload use case. Smartphones or other mobile devices equipped with two wireless interfaces are a very common use case for Multipath TCP. In September 2015, this is also the largest deployment of Multipath-TCP enabled devices [IOS7]. It Bonaventure, et al. Expires March 2, 2017 [Page 5] Internet-Draft MPTCP Experience August 2016 has been briefly discussed during IETF88 [ietf88], but there is no published paper or report that analyses this deployment. For this reason, we only discuss published papers that have mainly used the Multipath TCP implementation in the Linux kernel for their experiments. The performance of Multipath TCP in wireless networks was briefly evaluated in [NSDI12]. One experiment analyzes the performance of Multipath TCP on a client with two wireless interfaces. This evaluation shows that when the receive window is large, Multipath TCP can efficiently use the two available links. However, if the window becomes smaller, then packets sent on a slow path can block the transmission of packets on a faster path. In some cases, the performance of Multipath TCP over two paths can become lower than the performance of regular TCP over the best performing path. Two heuristics, reinjection and penalization, are proposed in [NSDI12] to solve this identified performance problem. These two heuristics have since been used in the Multipath TCP implementation in the Linux kernel. [CONEXT13] explored the problem in more detail and revealed some other scenarios where Multipath TCP can have difficulties in efficiently pooling the available paths. Improvements to the Multipath TCP implementation in the Linux kernel are proposed in [CONEXT13] to cope with some of these problems. The first experimental analysis of Multipath TCP in a public wireless environment was presented in [Cellnet12]. These measurements explore the ability of Multipath TCP to use two wireless networks (real WiFi and 3G networks). Three modes of operation are compared. The first mode of operation is the simultaneous use of the two wireless networks. In this mode, Multipath TCP pools the available resources and uses both wireless interfaces. This mode provides fast handover from WiFi to cellular or the opposite when the user moves. Measurements presented in [CACM14] show that the handover from one wireless network to another is not an abrupt process. When a host moves, there are regions where the quality of one of the wireless networks is weaker than the other, but the host considers this wireless network to still be up. When a mobile host enters such regions, its ability to send packets over another wireless network is important to ensure a smooth handover. This is clearly illustrated from the packet trace discussed in [CACM14]. Many cellular networks use volume-based pricing and users often prefer to use unmetered WiFi networks when available instead of metered cellular networks. [Cellnet12] implements support for the MP_PRIO option to explore two other modes of operation. In the backup mode, Multipath TCP opens a TCP subflow over each interface, but the cellular interface is configured in backup mode. Bonaventure, et al. Expires March 2, 2017 [Page 6] Internet-Draft MPTCP Experience August 2016 This implies that data flows only over the WiFi interface when both interfaces are considered to be active. If the WiFi interface fails, then the traffic switches quickly to the cellular interface, ensuring a smooth handover from the user's viewpoint [Cellnet12]. The cost of this approach is that the WiFi and cellular interfaces are likely to remain active all the time since all subflows are established over the two interfaces. The single-path mode is slightly different. This mode benefits from the break-before-make capability of Multipath TCP. When an MPTCP session is established, a subflow is created over the WiFi interface. No packet is sent over the cellular interface as long as the WiFi interface remains up [Cellnet12]. This implies that the cellular interface can remain idle and battery capacity is preserved. When the WiFi interface fails, a new subflow is established over the cellular interface in order to preserve the established Multipath TCP sessions. Compared to the backup mode described earlier, measurements reported in [Cellnet12] indicate that this mode of operation is characterised by a throughput drop while the cellular interface is brought up and the subflows are reestablished. From a protocol viewpoint, [Cellnet12] discusses the problem posed by the unreliability of the REMOVE_ADDR option and proposes a small protocol extension to allow hosts to reliably exchange this option. It would be useful to analyze packet traces to understand whether the unreliability of the REMOVE_ADDR option poses an operational problem in real deployments. Another study of the performance of Multipath TCP in wireless networks was reported in [IMC13b]. This study uses laptops connected to various cellular ISPs and WiFi hotspots. It compares various file transfer scenarios. [IMC13b] observes that 4-path MPTCP outperforms 2-path MPTCP, especially for larger files. However, for three congestion control algorithms (LIA, OLIA and Reno - see Section 3.2), there is no significant performance difference for file sizes smaller than 4MB. A different study of the performance of Multipath TCP with two wireless networks is presented in [INFOCOM14]. In this study the two networks had different qualities : a good network and a lossy network. When using two paths with different packet loss ratios, the Multipath TCP congestion control scheme moves traffic away from the lossy link that is considered to be congested. However, [INFOCOM14] documents an interesting scenario that is summarised in Figure 1. Bonaventure, et al. Expires March 2, 2017 [Page 7] Internet-Draft MPTCP Experience August 2016 client ----------- path1 -------- server | | +--------------- path2 ------------+ Figure 1: Simple network topology Initially, the two paths have the same quality and Multipath TCP distributes the load over both of them. During the transfer, the second path becomes lossy, e.g. because the client moves. Multipath TCP detects the packet losses and they are retransmitted over the first path. This enables the data transfer to continue over the first path. However, the subflow over the second path is still up and transmits one packet from time to time. Although the N packets have been acknowledged over the first subflow (at the MPTCP level), they have not been acknowledged at the TCP level over the second subflow. To preserve the continuity of the sequence numbers over the second subflow, TCP will continue to retransmit these segments until either they are acknowledged or the maximum number of retransmissions is reached. This behavior is clearly inefficient and may lead to blocking since the second subflow will consume window space to be able to retransmit these packets. [INFOCOM14] proposes a new Multipath TCP option to solve this problem. In practice, a new TCP option is probably not required. When the client detects that the data transmitted over the second subflow has been acknowledged over the first subflow, it could decide to terminate the second subflow by sending a RST segment. If the interface associated to this subflow is still up, a new subflow could be immediately reestablished. It would then be immediately usable to send new data and would not be forced to first retransmit the previously transmitted data. As of this writing, this dynamic management of the subflows is not yet implemented in the Multipath TCP implementation in the Linux kernel. Some studies have started to analyse the performance of Multipath TCP on smartphones with real applications. In contrast with the bulk transfers that are used by many publications, real applications do not exchange huge amounts of data and establish a large number of small connections. [COMMAG2016] proposes a software testing framework that allows to automate Android applications to study their interactions with Multipath TCP. [PAM2016] analyses a one-month packet trace of all the packets exchanged by a dozen of smartphones used by regular users. This analysis reveals that short connections are important on smartphones and that the main benefit of using Multipath TCP on smartphones is the ability to perform seamless handovers between different wireless networks. Long connections benefit from these handovers. Bonaventure, et al. Expires March 2, 2017 [Page 8] Internet-Draft MPTCP Experience August 2016 2.3. Multipath TCP proxies As Multipath TCP is not yet widely deployed on both clients and servers, several deployments have used various forms of proxies. Two families of solutions are currently being used or tested. A first use case is when a Multipath TCP enabled client wants to use several interfaces to reach a regular TCP server. A typical use case is a smartphone that needs to use both its WiFi and its cellular interface to transfer data. Several types of proxies are possible for this use case. An HTTP proxy deployed on a Multipath TCP capable server would enable the smartphone to use Multipath TCP to access regular web servers. Obviously, this solution only works for applications that rely on HTTP. Another possibility is to use a proxy that can convert any Multipath TCP connection into a regular TCP connection. Multipath TCP-specific proxies have been proposed [HotMiddlebox13b] [HAMPEL]. Another possibility leverages the SOCKS protocol [RFC1928]. SOCKS is often used in enterprise networks to allow clients to reach external servers. For this, the client opens a TCP connection to the SOCKS server that relays it to the final destination. If both the client and the SOCKS server use Multipath TCP, but not the final destination, then Multipath TCP can still be used on the path between the client and the SOCKS server. At IETF'93, Korea Telecom announced that they have deployed in June 2015 a commercial service that uses Multipath TCP on smartphones. These smartphones access regular TCP servers through a SOCKS proxy. This enables them to achieve throughputs of up to 850 Mbps [KT]. Measurements performed with Android smartphones [Mobicom15] show that popular applications work correctly through a SOCKS proxy and Multipath TCP enabled smartphones. Thanks to Multipath TCP, long- lived connections can be spread over the two available interfaces. However, for short-lived connections, most of the data is sent over the initial subflow that is created over the interface corresponding to the default route and the second subflow is almost not used [PAM2016]. A second use case is when Multipath TCP is used by middleboxes, typically inside access networks. Various network operators are discussing and evaluating solutions for hybrid access networks [BBF-WT348]. Such networks arise when a network operator controls two different access network technologies, e.g. wired and cellular, and wants to combine them to improve the bandwidth offered to the endusers [I-D.lhwxz-hybrid-access-network-architecture]. Several solutions are currently investigated for such networks [BBF-WT348]. Figure 2 shows the organisation of such a network. When a client Bonaventure, et al. Expires March 2, 2017 [Page 9] Internet-Draft MPTCP Experience August 2016 creates a normal TCP connection, it is intercepted by the Hybrid CPE (HPCE) that converts it in a Multipath TCP connection so that it can use the available access networks (DSL and LTE in the example). The Hybrid Access Gateway (HAG) does the opposite to ensure that the regular server sees a normal TCP connection. Some of the solutions that are currently discussed for hybrid networks use Multipath TCP on the HCPE and the HAG. Other solutions rely on tunnels between the HCPE and the HAG [I-D.lhwxz-gre-notifications-hybrid-access]. client --- HCPE ------ DSL ------- HAG --- internet --- server | | +------- LTE -----------+ Figure 2: Hybrid Access Network Bonaventure, et al. Expires March 2, 2017 [Page 10] Internet-Draft MPTCP Experience August 2016 3. Operational Experience 3.1. Middlebox interference The interference caused by various types of middleboxes has been an important concern during the design of the Multipath TCP protocol. Three studies on the interactions between Multipath TCP and middleboxes are worth discussing. The first analysis appears in [IMC11]. This paper was the main motivation for Multipath TCP incorporating various techniques to cope with middlebox interference. More specifically, Multipath TCP has been designed to cope with middleboxes that : o change source or destination addresses o change source or destination port numbers o change TCP sequence numbers o split or coalesce segments o remove TCP options o modify the payload of TCP segments These middlebox interferences have all been included in the MBtest suite [MBTest]. This test suite is used in [HotMiddlebox13] to verify the reaction of the Multipath TCP implementation in the Linux kernel [MultipathTCP-Linux] when faced with middlebox interference. The test environment used for this evaluation is a dual-homed client connected to a single-homed server. The middlebox behavior can be activated on any of the paths. The main results of this analysis are : o the v0.87 Multipath TCP implementation in the Linux kernel is not affected by a middlebox that performs NAT or modifies TCP sequence numbers o when a middlebox removes the MP_CAPABLE option from the initial SYN segment, the v0.87 Multipath TCP implementation in the Linux kernel falls back correctly to regular TCP o when a middlebox removes the DSS option from all data segments, the v0.87 Multipath TCP implementation in the Linux kernel falls back correctly to regular TCP Bonaventure, et al. Expires March 2, 2017 [Page 11] Internet-Draft MPTCP Experience August 2016 o when a middlebox performs segment coalescing, the v0.87 Multipath TCP implementation in the Linux kernel is still able to accurately extract the data corresponding to the indicated mapping o when a middlebox performs segment splitting, the v0.87 Multipath TCP implementation in the Linux kernel correctly reassembles the data corresponding to the indicated mapping. [HotMiddlebox13] shows on figure 4 in section 3.3 a corner case with segment splitting that may lead to a desynchronisation between the two hosts. The interactions between Multipath TCP and real deployed middleboxes is also analyzed in [HotMiddlebox13] and a particular scenario with the FTP application level gateway running on a NAT is described. Middlebox interference can also be detected by analysing packet traces on Multipath TCP enabled servers. A closer look at the packets received on the multipath-tcp.org server [TMA2015] shows that among the 184,000 Multipath TCP connections, only 125 of them were falling back to regular TCP. These connections originated from 28 different client IP addresses. These include 91 HTTP connections and 34 FTP connections. The FTP interference is expected and due to Application Level Gateways running home routers. The HTTP interference appeared only on the direction from server to client and could have been caused by transparent proxies deployed in cellular or enterprise networks. A longer trace is discussed in [COMCOM2016] and similar conclusions about the middlebox interference are provided. From an operational viewpoint, knowing that Multipath TCP can cope with various types of middlebox interference is important. However, there are situations where the network operators need to gather information about where a particular middlebox interference occurs. The tracebox software [tracebox] described in [IMC13a] is an extension of the popular traceroute software that enables network operators to check at which hop a particular field of the TCP header (including options) is modified. It has been used by several network operators to debug various middlebox interference problems. Experience with tracebox indicates that supporting the ICMP extension defined in [RFC1812] makes it easier to debug middlebox problems in IPv4 networks. Users of the Multipath TCP implementation have reported some experience with middlebox interference. The strangest scenario has been a middlebox that accepts the Multipath TCP options in the SYN segment but later replaces Multipath TCP options with a TCP EOL option [StrangeMbox]. This causes Multipath TCP to perform a fallback to regular TCP without any impact on the application. Bonaventure, et al. Expires March 2, 2017 [Page 12] Internet-Draft MPTCP Experience August 2016 3.2. Congestion control Congestion control has been an important challenge for Multipath TCP. The standardised congestion control scheme for Multipath TCP is defined in [RFC6356]. A detailed description of this algorithm is provided in [NSDI11]. This congestion control scheme has been implemented in the Linux implementation of Multipath TCP. Linux uses a modular architecture to support various congestion control schemes. This architecture is applicable for both regular TCP and Multipath TCP. While the coupled congestion control scheme defined in [RFC6356] is the default congestion control scheme in the Linux implementation, other congestion control schemes have been added. The second congestion control scheme is OLIA [CONEXT12]. This congestion control scheme is also an adaptation of the NewReno single path congestion control scheme to support multiple paths. Simulations and measurements have shown that it provides some performance benefits compared to the the default congestion control scheme [CONEXT12]. Measurements over a wide range of parameters reported in [CONEXT13] also indicate some benefits with the OLIA congestion control scheme. Recently, a delay-based congestion control scheme has been ported to the Multipath TCP implementation in the Linux kernel. This congestion control scheme has been evaluated by using simulations in [ICNP12]. The fourth congestion control scheme that has been included in the Linux implementation of Multipath TCP is the BALIA scheme that provides a better balance between TCP friendliness, responsiveness, and window oscillation [BALIA]. These different congestion control schemes have been compared in several articles. [CONEXT13] and [PaaschPhD] compare these algorithms in an emulated environment. The evaluation showed that the delay-based congestion control scheme is less able to efficiently use the available links than the three other schemes. Reports from some users indicate that they seem to favor OLIA. 3.3. Subflow management The multipath capability of Multipath TCP comes from the utilisation of one subflow per path. The Multipath TCP architecture [RFC6182] and the protocol specification [RFC6824] define the basic usage of the subflows and the protocol mechanisms that are required to create and terminate them. However, there are no guidelines on how subflows are used during the lifetime of a Multipath TCP session. Most of the published experiments with Multipath TCP have been performed in controlled environments. Still, based on the experience running them and discussions on the mptcp-dev mailing list, interesting lessons have been learned about the management of these subflows. Bonaventure, et al. Expires March 2, 2017 [Page 13] Internet-Draft MPTCP Experience August 2016 From a subflow viewpoint, the Multipath TCP protocol is completely symmetrical. Both the clients and the server have the capability to create subflows. However in practice the existing Multipath TCP implementations have opted for a strategy where only the client creates new subflows. The main motivation for this strategy is that often the client resides behind a NAT or a firewall, preventing passive subflow openings on the client. Although there are environments such as datacenters where this problem does not occur, as of this writing, no precise requirement has emerged for allowing the server to create new subflows. 3.4. Implemented subflow managers The Multipath TCP implementation in the Linux kernel includes several strategies to manage the subflows that compose a Multipath TCP session. The basic subflow manager is the full-mesh. As the name implies, it creates a full-mesh of subflows between the communicating hosts. The most frequent use case for this subflow manager is a multihomed client connected to a single-homed server. In this case, one subflow is created for each interface on the client. The current implementation of the full-mesh subflow manager is static. The subflows are created immediately after the creation of the initial subflow. If one subflow fails during the lifetime of the Multipath TCP session (e.g. due to excessive retransmissions, or the loss of the corresponding interface), it is not always reestablished. There is ongoing work to enhance the full-mesh path manager to deal with such events. When the server is multihomed, using the full-mesh subflow manager may lead to a large number of subflows being established. For example, consider a dual-homed client connected to a server with three interfaces. In this case, even if the subflows are only created by the client, 6 subflows will be established. This may be excessive in some environments, in particular when the client and/or the server have a large number of interfaces. A recent draft has proposed a Multipath TCP option to negotiate the maximum number of subflows. However, it should be noted that there have been reports on the mptcp-dev mailing indicating that users rely on Multipath TCP to aggregate more than four different interfaces. Thus, there is a need for supporting many interfaces efficiently. Creating subflows between multihomed clients and servers may sometimes lead to operational issues as observed by discussions on the mptcp-dev mailing list. In some cases the network operators would like to have a better control on how the subflows are created by Multipath TCP [I-D.boucadair-mptcp-max-subflow]. This might Bonaventure, et al. Expires March 2, 2017 [Page 14] Internet-Draft MPTCP Experience August 2016 require the definition of policy rules to control the operation of the subflow manager. The two scenarios below illustrate some of these requirements. host1 ---------- switch1 ----- host2 | | | +-------------- switch2 --------+ Figure 3: Simple switched network topology Consider the simple network topology shown in Figure 3. From an operational viewpoint, a network operator could want to create two subflows between the communicating hosts. From a bandwidth utilization viewpoint, the most natural paths are host1-switch1-host2 and host1-switch2-host2. However, a Multipath TCP implementation running on these two hosts may sometimes have difficulties to obtain this result. To understand the difficulty, let us consider different allocation strategies for the IP addresses. A first strategy is to assign two subnets : subnetA (resp. subnetB) contains the IP addresses of host1's interface to switch1 (resp. switch2) and host2's interface to switch1 (resp. switch2). In this case, a Multipath TCP subflow manager should only create one subflow per subnet. To enforce the utilization of these paths, the network operator would have to specify a policy that prefers the subflows in the same subnet over subflows between addresses in different subnets. It should be noted that the policy should probably also specify how the subflow manager should react when an interface or subflow fails. A second strategy is to use a single subnet for all IP addresses. In this case, it becomes more difficult to specify a policy that indicates which subflows should be established. The second subflow manager that is currently supported by the Multipath TCP implementation in the Linux kernel is the ndiffport subflow manager. This manager was initially created to exploit the path diversity that exists between single-homed hosts due to the utilization of flow-based load balancing techniques [SIGCOMM11]. This subflow manager creates N subflows between the same pair of IP addresses. The N subflows are created by the client and differ only in the source port selected by the client. It was not designed to be used on multihomed hosts. A more flexible subflow manager has been proposed, implemented and evaluated in [CONEXT15]. This subflow manager exposes various kernel events to a user space daemon that decides when subflows need to be Bonaventure, et al. Expires March 2, 2017 [Page 15] Internet-Draft MPTCP Experience August 2016 created and terminated based on various policies. 3.5. Subflow destination port The Multipath TCP protocol relies on the token contained in the MP_JOIN option to associate a subflow to an existing Multipath TCP session. This implies that there is no restriction on the source address, destination address and source or destination ports used for the new subflow. The ability to use different source and destination addresses is key to support multihomed servers and clients. The ability to use different destination port numbers is worth discussing because it has operational implications. For illustration, consider a dual-homed client that creates a second subflow to reach a single-homed server as illustrated in Figure 4. client ------- r1 --- internet --- server | | +----------r2-------+ Figure 4: Multihomed-client connected to single-homed server When the Multipath TCP implementation in the Linux kernel creates the second subflow it uses the same destination port as the initial subflow. This choice is motivated by the fact that the server might be protected by a firewall and only accept TCP connections (including subflows) on the official port number. Using the same destination port for all subflows is also useful for operators that rely on the port numbers to track application usage in their network. There have been suggestions from Multipath TCP users to modify the implementation to allow the client to use different destination ports to reach the server. This suggestion seems mainly motivated by traffic shaping middleboxes that are used in some wireless networks. In networks where different shaping rates are associated to different destination port numbers, this could allow Multipath TCP to reach a higher performance. As of this writing, we are not aware of any implementation of this kind of tweaking. However, from an implementation point-of-view supporting different destination ports for the same Multipath TCP connection can cause some issues. A legacy implementation of a TCP stack creates a listening socket to react upon incoming SYN segments. The listening socket is handling the SYN segments that are sent on a specific port number. Demultiplexing incoming segments can thus be done solely by looking at the IP addresses and the port numbers. With Multipath TCP however, incoming SYN segments may have an MP_JOIN option with a Bonaventure, et al. Expires March 2, 2017 [Page 16] Internet-Draft MPTCP Experience August 2016 different destination port. This means, that all incoming segments that did not match on an existing listening-socket or an already established socket must be parsed for an eventual MP_JOIN option. This imposes an additional cost on servers, previously not existent on legacy TCP implementations. 3.6. Closing subflows client server | | MPTCP: established | | MPTCP: established Sub: established | | Sub: established | | | DATA_FIN | MPTCP: close-wait | <------------------------ | close() (step 1) Sub: established | DATA_ACK | | ------------------------> | MPTCP: fin-wait-2 | | Sub: established | | | DATA_FIN + subflow-FIN | close()/shutdown() | ------------------------> | MPTCP: time-wait (step 2) | DATA_ACK | Sub: close-wait MPTCP: closed | <------------------------ | Sub: fin-wait-2 | | | | | subflow-FIN | MPTCP: closed | <------------------------ | subflow-close() Sub: time-wait | subflow-ACK | (step 3) | ------------------------> | MPTCP: time-wait | | Sub: closed | | Figure 5: Multipath TCP may not be able to avoid time-wait state on the subflow (indicated as Sub in the drawing), even if enforced by the application on the client-side. Figure 5 shows a very particular issue within Multipath TCP. Many high-performance applications try to avoid Time-Wait state by deferring the closure of the connection until the peer has sent a FIN. That way, the client on the left of Figure 5 does a passive closure of the connection, transitioning from Close-Wait to Last-ACK and finally freeing the resources after reception of the ACK of the FIN. An application running on top of a Multipath TCP enabled Linux kernel might also use this approach. The difference here is that the close() of the connection (Step 1 in Figure 5) only triggers the sending of a DATA_FIN. Nothing guarantees that the kernel is ready to combine the DATA_FIN with a subflow-FIN. The reception of the Bonaventure, et al. Expires March 2, 2017 [Page 17] Internet-Draft MPTCP Experience August 2016 DATA_FIN will make the application trigger the closure of the connection (step 2), trying to avoid Time-Wait state with this late closure. This time, the kernel might decide to combine the DATA_FIN with a subflow-FIN. This decision will be fatal, as the subflow's state machine will not transition from Close-Wait to Last-Ack, but rather go through Fin-Wait-2 into Time-Wait state. The Time-Wait state will consume resources on the host for at least 2 MSL (Maximum Segment Lifetime). Thus, a smart application that tries to avoid Time-Wait state by doing late closure of the connection actually ends up with one of its subflows in Time-Wait state. A high-performance Multipath TCP kernel implementation should honor the desire of the application to do passive closure of the connection and successfully avoid Time-Wait state - even on the subflows. The solution to this problem lies in an optimistic assumption that a host doing active-closure of a Multipath TCP connection by sending a DATA_FIN will soon also send a FIN on all its subflows. Thus, the passive closer of the connection can simply wait for the peer to send exactly this FIN - enforcing passive closure even on the subflows. Of course, to avoid consuming resources indefinitely, a timer must limit the time our implementation waits for the FIN. 3.7. Packet schedulers In a Multipath TCP implementation, the packet scheduler is the algorithm that is executed when transmitting each packet to decide on which subflow it needs to be transmitted. The packet scheduler itself does not have any impact on the interoperability of Multipath TCP implementations. However, it may clearly impact the performance of Multipath TCP sessions. The Multipath TCP implementation in the Linux kernel supports a pluggable architecture for the packet scheduler [PaaschPhD]. As of this writing, two schedulers have been implemented: round-robin and lowest-rtt-first. The second scheduler relies on the round-trip-time (rtt) measured on each TCP subflow and sends first segments over the subflow having the lowest round-trip- time. They are compared in [CSWS14]. The experiments and measurements described in [CSWS14] show that the lowest-rtt-first scheduler appears to be the best compromise from a performance viewpoint. Another study of the packet schedulers is presented in [PAMS2014]. This study relies on simulations with the Multipath TCP implementation in the Linux kernel. They compare the lowest-rtt- first with the round-robin and a random scheduler. They show some situations where the lowest-rtt-first scheduler does not perform as well as the other schedulers, but there are many scenarios where the opposite is true. [PAMS2014] notes that "it is highly likely that the optimal scheduling strategy depends on the characteristics of the paths being used." Bonaventure, et al. Expires March 2, 2017 [Page 18] Internet-Draft MPTCP Experience August 2016 3.8. Segment size selection When an application performs a write/send system call, the kernel allocates a packet buffer (sk_buff in Linux) to store the data the application wants to send. The kernel will store at most one MSS (Maximum Segment Size) of data per buffer. As the MSS can differ amongst subflows, an MPTCP implementation must select carefully the MSS used to generate application data. The Linux kernel implementation had various ways of selecting the MSS: minimum or maximum amongst the different subflows. However, these heuristics of MSS selection can cause significant performance issues in some environment. Consider the following example. An MPTCP connection has two established subflows that respectively use a MSS of 1420 and 1428 bytes. If MPTCP selects the maximum, then the application will generate segments of 1428 bytes of data. An MPTCP implementation will have to split the segment in two (a 1420-byte and 8-byte segments) when pushing on the subflow with the smallest MSS. The latter segment will introduce a large overhead as for a single data segment 2 slots will be used in the congestion window (in packets) therefore reducing by roughly twice the potential throughput (in bytes/s) of this subflow. Taking the smallest MSS does not solve the issue as there might be a case where the subflow with the smallest MSS only sends a few packets therefore reducing the potential throughput of the other subflows. The Linux implementation recently took another approach [DetalMSS]. Instead of selecting the minimum and maximum values, it now dynamically adapts the MSS based on the contribution of all the subflows to the connection's throughput. For this it computes, for each subflow, the potential throughput achieved by selecting each MSS value and by taking into account the lost space in the cwnd. It then selects the MSS that allows to achieve the highest potential throughput. 3.9. Interactions with the Domain Name System Multihomed clients such as smartphones can send DNS queries over any of their interfaces. When a single-homed client performs a DNS query, it receives from its local resolver the best answer for its request. If the client is multihomed, the answer returned to the DNS query may vary with the interface over which it has been sent. Bonaventure, et al. Expires March 2, 2017 [Page 19] Internet-Draft MPTCP Experience August 2016 cdn1 | client -- cellular -- internet -- cdn3 | | +----- wifi --------+ | cdn2 Figure 6: Simple network topology If the client sends a DNS query over the WiFi interface, the answer will point to the cdn2 server while the same request sent over the cellular interface will point to the cdn1 server. This might cause problems for CDN providers that locate their servers inside ISP networks and have contracts that specify that the CDN server will only be accessed from within this particular ISP. Assume now that both the client and the CDN servers support Multipath TCP. In this case, a Multipath TCP session from cdn1 or cdn2 would potentially use both the cellular network and the WiFi network. Serving the client from cdn2 over the cellular interface could violate the contract between the CDN provider and the network operators. A similar problem occurs with regular TCP if the client caches DNS replies. For example the client obtains a DNS answer over the cellular interface and then stops this interface and starts to use its WiFi interface. If the client retrieves data from cdn1 over its WiFi interface, this may also violate the contract between the CDN and the network operators. A possible solution to prevent this problem would be to modify the DNS resolution on the client. The client subnet EDNS extension defined in [RFC7871] could be used for this purpose. When the client sends a DNS query from its WiFi interface, it should also send the client subnet corresponding to the cellular interface in this request. This would indicate to the resolver that the answer should be valid for both the WiFi and the cellular interfaces (e.g., the cdn3 server). 3.10. Captive portals Multipath TCP enables a host to use different interfaces to reach a server. In theory, this should ensure connectivity when at least one of the interfaces is active. In practice however, there are some particular scenarios with captive portals that may cause operational problems. The reference environment is shown in Figure 7. Bonaventure, et al. Expires March 2, 2017 [Page 20] Internet-Draft MPTCP Experience August 2016 client ----- network1 | +------- internet ------------- server Figure 7: Issue with captive portal The client is attached to two networks : network1 that provides limited connectivity and the entire Internet through the second network interface. In practice, this scenario corresponds to an open WiFi network with a captive portal for network1 and a cellular service for the second interface. On many smartphones, the WiFi interface is preferred over the cellular interface. If the smartphone learns a default route via both interfaces, it will typically prefer to use the WiFi interface to send its DNS request and create the first subflow. This is not optimal with Multipath TCP. A better approach would probably be to try a few attempts on the WiFi interface and then try to use the second interface for the initial subflow as well. 3.11. Stateless webservers MPTCP has been designed to interoperate with webservers that benefit from SYN-cookies to protect against SYN-flooding attacks [RFC4987]. MPTCP achieves this by echoing the keys negotiated during the MP_CAPABLE handshake in the third ACK of the 3-way handshake. Reception of this third ACK then allows the server to reconstruct the state specific to MPTCP. However, one caveat to this mechanism is the non-reliable nature of the third ACK. Indeed, when the third ACK gets lost, the server will not be able to reconstruct the MPTCP-state. MPTCP will fallback to regular TCP in this case. This is in contrast to regular TCP. When the client starts sending data, the first data segment also includes the SYN-cookie, which allows the server to reconstruct the TCP-state. Further, this data segment will be retransmitted by the client in case it gets lost and thus is resilient against loss. MPTCP does not include the keys in this data segment and thus the server cannot reconstruct the MPTCP state. This issue might be considered as a minor one for MPTCP. Losing the third ACK should only happen when packet loss is high. However, when packet-loss is high MPTCP provides a lot of benefits as it can move traffic away from the lossy link. It is undesirable that MPTCP has a higher chance to fall back to regular TCP in those lossy environments. [I-D.paasch-mptcp-syncookies] discusses this issue and suggests a Bonaventure, et al. Expires March 2, 2017 [Page 21] Internet-Draft MPTCP Experience August 2016 modified handshake mechanism that ensures reliable delivery of the MP_CAPABLE, following the 3-way handshake. This modification will make MPTCP reliable, even in lossy environments when servers need to use SYN-cookies to protect against SYN-flooding attacks. 3.12. Loadbalanced serverfarms Large-scale serverfarms typically deploy thousands of servers behind a single virtual IP (VIP). Steering traffic to these servers is done through layer-4 loadbalancers that ensure that a TCP-flow will always be routed to the same server [Presto08]. As Multipath TCP uses multiple different TCP subflows to steer the traffic across the different paths, loadbalancers need to ensure that all these subflows are routed to the same server. This implies that the loadbalancers need to track the MPTCP-related state, allowing them to parse the token in the MP_JOIN and assign those subflows to the appropriate server. However, serverfarms typically deploy multiple of these loadbalancers for reliability and capacity reasons. As a TCP subflow might get routed to any of these loadbalancers, they would need to synchronize the MPTCP-related state - a solution that is not feasible at large scale. The token (carried in the MP_JOIN) contains the information indicating which MPTCP-session the subflow belongs to. As the token is a hash of the key, servers are not able to generate the token in such a way that the token can provide the necessary information to the loadbalancers which would allow them to route TCP subflows to the appropriate server. [I-D.paasch-mptcp-loadbalancer] discusses this issue in detail and suggests two alternative MP_CAPABLE handshakes to overcome these. As of September 2015, it is not yet clear how MPTCP might accomodate such use-case to enable its deployment within loadbalanced serverfarms. Bonaventure, et al. Expires March 2, 2017 [Page 22] Internet-Draft MPTCP Experience August 2016 4. IANA Considerations There are no IANA considerations in this informational document. Bonaventure, et al. Expires March 2, 2017 [Page 23] Internet-Draft MPTCP Experience August 2016 5. Security Considerations The security considerations for Multipath TCP have already been documented in [RFC6181], [RFC6182], [RFC6824] and [RFC7430]. Bonaventure, et al. Expires March 2, 2017 [Page 24] Internet-Draft MPTCP Experience August 2016 6. Acknowledgements This work was partially supported by the FP7-Trilogy2 project. We would like to thank all the implementers and users of the Multipath TCP implementation in the Linux kernel. This document has benefited from the comments of John Ronan, Yoshifumi Nishida, Phil Eardley, Jaehyun Hwang and Mirja Kuehlewind. Bonaventure, et al. Expires March 2, 2017 [Page 25] Internet-Draft MPTCP Experience August 2016 7. Informative References [Apple-MPTCP] Apple, Inc, ., "iOS - Multipath TCP Support in iOS 7", n.d., . [BALIA] Peng, Q., Walid, A., Hwang, J., and S. Low, "Multipath TCP Analysis, Design, and Implementation", IEEE/ACM Trans. on Networking, Vol. 24, No. 1 , 2016. [BBF-WT348] Fabregas (Ed), G., "WT-348 - Hybrid Access for Broadband Networks", Broadband Forum, contribution bbf2014.1139.04 , June 2015. [CACM14] Paasch, C. and O. Bonaventure, "Multipath TCP", Communications of the ACM, 57(4):51-57 , April 2014, . [COMCOM2016] "Observing real Multipath TCP traffic", Computer Communications , April 2016, . [COMMAG2016] De Coninck, Q., Baerts, M., Hesmans, B., and O. Bonaventure, "Observing Real Smartphone Applications over Multipath TCP", IEEE Communications Magazine , March 2016, . [CONEXT12] Khalili, R., Gast, N., Popovic, M., Upadhyay, U., and J. Leboudec, "MPTCP is not pareto-optimal performance issues and a possible solution", Proceedings of the 8th international conference on Emerging networking experiments and technologies (CoNEXT12) , 2012. [CONEXT13] Paasch, C., Khalili, R., and O. Bonaventure, "On the Benefits of Applying Experimental Design to Improve Multipath TCP", Conference on emerging Networking EXperiments and Technologies (CoNEXT) , December 2013, . Bonaventure, et al. Expires March 2, 2017 [Page 26] Internet-Draft MPTCP Experience August 2016 [CONEXT15] Hesmans, B., Detal, G., Barre, S., Bauduin, R., and O. Bonaventure, "SMAPP - Towards Smart Multipath TCP-enabled APPlications", Proc. Conext 2015, Heidelberg, Germany , December 2015, . [CSWS14] Paasch, C., Ferlin, S., Alay, O., and O. Bonaventure, "Experimental Evaluation of Multipath TCP Schedulers", SIGCOMM CSWS2014 workshop , August 2014. [Cellnet12] Paasch, C., Detal, G., Duchene, F., Raiciu, C., and O. Bonaventure, "Exploring Mobile/WiFi Handover with Multipath TCP", ACM SIGCOMM workshop on Cellular Networks (Cellnet12) , 2012, . [DetalMSS] Detal, G., "Adaptive MSS value", Post on the mptcp-dev mailing list , September 2014, . [FreeBSD-MPTCP] Williams, N., "Multipath TCP For FreeBSD Kernel Patch v0.5", n.d., . [HAMPEL] Hampel, G., Rana, A., and T. Klein, "Seamless TCP mobility using lightweight MPTCP proxy", Proceedings of the 11th ACM international symposium on Mobility management and wireless access (MobiWac '13). , 2013. [HotMiddlebox13] Hesmans, B., Duchene, F., Paasch, C., Detal, G., and O. Bonaventure, "Are TCP Extensions Middlebox-proof?", CoNEXT workshop HotMiddlebox , December 2013, . [HotMiddlebox13b] Detal, G., Paasch, C., and O. Bonaventure, "Multipath in the Middle(Box)", HotMiddlebox'13 , December 2013, . [HotNets] Raiciu, C., Pluntke, C., Barre, S., Greenhalgh, A., Wischik, D., and M. Handley, "Data center networking with multipath TCP", Proceedings of the 9th ACM SIGCOMM Bonaventure, et al. Expires March 2, 2017 [Page 27] Internet-Draft MPTCP Experience August 2016 Workshop on Hot Topics in Networks (Hotnets-IX) , 2010, . [I-D.boucadair-mptcp-max-subflow] Boucadair, M. and C. Jacquenet, "Negotiating the Maximum Number of Multipath TCP (MPTCP) Subflows", draft-boucadair-mptcp-max-subflow-02 (work in progress), May 2016. [I-D.lhwxz-gre-notifications-hybrid-access] Leymann, N., Heidemann, C., Wasserman, M., Xue, L., and M. Zhang, "GRE Notifications for Hybrid Access", draft-lhwxz-gre-notifications-hybrid-access-01 (work in progress), January 2015. [I-D.lhwxz-hybrid-access-network-architecture] Leymann, N., Heidemann, C., Wasserman, M., Xue, L., and M. Zhang, "Hybrid Access Network Architecture", draft-lhwxz-hybrid-access-network-architecture-02 (work in progress), January 2015. [I-D.paasch-mptcp-loadbalancer] Paasch, C., Greenway, G., and A. Ford, "Multipath TCP behind Layer-4 loadbalancers", draft-paasch-mptcp-loadbalancer-00 (work in progress), September 2015. [I-D.paasch-mptcp-syncookies] Paasch, C., Biswas, A., and D. Haas, "Making Multipath TCP robust for stateless webservers", draft-paasch-mptcp-syncookies-02 (work in progress), October 2015. [ICNP12] Cao, Y., Xu, M., and X. Fu, "Delay-based congestion control for multipath TCP", 20th IEEE International Conference on Network Protocols (ICNP) , 2012. [IMC11] Honda, M., Nishida, Y., Raiciu, C., Greenhalgh, A., Handley, M., and H. Tokuda, "Is it still possible to extend TCP?", Proceedings of the 2011 ACM SIGCOMM conference on Internet measurement conference (IMC '11) , 2011, . [IMC13a] Detal, G., Hesmans, B., Bonaventure, O., Vanaubel, Y., and B. Donnet, "Revealing Middlebox Interference with Tracebox", Proceedings of the 2013 ACM SIGCOMM conference on Internet measurement conference , 2013, . [IMC13b] Chen, Y., Lim, Y., Gibbens, R., Nahum, E., Khalili, R., and D. Towsley, "A measurement-based study of MultiPath TCP performance over wireless network", Proceedings of the 2013 conference on Internet measurement conference (IMC '13) , n.d., . [IMC13c] Pelsser, C., Cittadini, L., Vissicchio, S., and R. Bush, "From Paris to Tokyo on the suitability of ping to measure latency", Proceedings of the 2013 conference on Internet measurement conference (IMC '13) , 2013, . [INFOCOM14] Lim, Y., Chen, Y., Nahum, E., Towsley, D., and K. Lee, "Cross-Layer Path Management in Multi-path Transport Protocol for Mobile Devices", IEEE INFOCOM'14 , 2014. [IOS7] Apple, ., "Multipath TCP Support in iOS 7", January 2014, . [KT] Seo, S., "KT's GiGA LTE", July 2015, . [MBTest] Hesmans, B., "MBTest", 2013, . [MPTCPBIB] Bonaventure, O., "Multipath TCP - An annotated bibliography", Technical report , April 2015, . [Mobicom15] De Coninck, Q., Baerts, M., Hesmans, B., and O. Bonaventure, "Poster - Evaluating Android Applications with Multipath TCP", Mobicom 2015 (Poster) , September 2015. [MultipathTCP-Linux] Paasch, C., Barre, S., and . et al, "Multipath TCP implementation in the Linux kernel", n.d., . [NSDI11] Wischik, D., Raiciu, C., Greenhalgh, A., and M. Handley, "Design, implementation and evaluation of congestion control for Multipath TCP", In Proceedings of the 8th USENIX conference on Networked systems design and Bonaventure, et al. Expires March 2, 2017 [Page 29] Internet-Draft MPTCP Experience August 2016 implementation (NSDI11) , 2011. [NSDI12] Raiciu, C., Paasch, C., Barre, S., Ford, A., Honda, M., Duchene, F., Bonaventure, O., and M. Handley, "How Hard Can It Be? Designing and Implementing a Deployable Multipath TCP", USENIX Symposium of Networked Systems Design and Implementation (NSDI12) , April 2012, . [PAM2016] De Coninck, Q., Baerts, M., Hesmans, B., and O. Bonaventure, "A First Analysis of Multipath TCP on Smartphones", 17th International Passive and Active Measurements Conference (PAM2016) , March 2016, . [PAMS2014] Arzani, B., Gurney, A., Cheng, S., Guerin, R., and B. Loo, "Impact of Path Selection and Scheduling Policies on MPTCP Performance", PAMS2014 , 2014. [PaaschPhD] Paasch, C., "Improving Multipath TCP", Ph.D. Thesis , November 2014, . [Presto08] Greenberg, A., Lahiri, P., Maltz, D., Parveen, P., and S. Sengupta, "Towards a Next Generation Data Center Architecture - Scalability and Commoditization", ACM PRESTO 2008 , August 2008, . [RFC1812] Baker, F., Ed., "Requirements for IP Version 4 Routers", RFC 1812, DOI 10.17487/RFC1812, June 1995, . [RFC1928] Leech, M., Ganis, M., Lee, Y., Kuris, R., Koblas, D., and L. Jones, "SOCKS Protocol Version 5", RFC 1928, DOI 10.17487/RFC1928, March 1996, . [RFC4987] Eddy, W., "TCP SYN Flooding Attacks and Common Mitigations", RFC 4987, DOI 10.17487/RFC4987, August 2007, . Bonaventure, et al. Expires March 2, 2017 [Page 30] Internet-Draft MPTCP Experience August 2016 [RFC6181] Bagnulo, M., "Threat Analysis for TCP Extensions for Multipath Operation with Multiple Addresses", RFC 6181, DOI 10.17487/RFC6181, March 2011, . [RFC6182] Ford, A., Raiciu, C., Handley, M., Barre, S., and J. Iyengar, "Architectural Guidelines for Multipath TCP Development", RFC 6182, DOI 10.17487/RFC6182, March 2011, . [RFC6356] Raiciu, C., Handley, M., and D. Wischik, "Coupled Congestion Control for Multipath Transport Protocols", RFC 6356, DOI 10.17487/RFC6356, October 2011, . [RFC6824] Ford, A., Raiciu, C., Handley, M., and O. Bonaventure, "TCP Extensions for Multipath Operation with Multiple Addresses", RFC 6824, DOI 10.17487/RFC6824, January 2013, . [RFC7430] Bagnulo, M., Paasch, C., Gont, F., Bonaventure, O., and C. Raiciu, "Analysis of Residual Threats and Possible Fixes for Multipath TCP (MPTCP)", RFC 7430, DOI 10.17487/ RFC7430, July 2015, . [RFC7871] Contavalli, C., van der Gaast, W., Lawrence, D., and W. Kumari, "Client Subnet in DNS Queries", RFC 7871, DOI 10.17487/RFC7871, May 2016, . [SIGCOMM11] Raiciu, C., Barre, S., Pluntke, C., Greenhalgh, A., Wischik, D., and M. Handley, "Improving datacenter performance and robustness with multipath TCP", Proceedings of the ACM SIGCOMM 2011 conference , n.d., . [StrangeMbox] Bonaventure, O., "Multipath TCP through a strange middlebox", Blog post , January 2015, . [TMA2015] Hesmans, B., Tran Viet, H., Sadre, R., and O. Bonaventure, "A First Look at Real Multipath TCP Traffic", Traffic Monitoring and Analysis , 2015, . [ietf88] Stewart, L., "IETF'88 Meeting minutes of the MPTCP working group", n.d., . [tracebox] Detal, G. and O. Tilmans, "tracebox", 2013, . Bonaventure, et al. Expires March 2, 2017 [Page 32] Internet-Draft MPTCP Experience August 2016 Appendix A. Changelog This section should be removed before final publication o initial version : September 16th, 2014 : Added section Section 3.8 that discusses some performance problems that appeared with the Linux implementation when using subflows having different MSS values o update with a description of the middlebox that replaces an unknown TCP option with EOL [StrangeMbox] o version ietf-02 : July 2015, answer to last call comments * Reorganised text to better separate use cases and operational experience * New use case on Multipath TCP proxies in Section 2.3 * Added some text on middleboxes in Section 3.1 * Removed the discussion on SDN * Restructured text and improved writing in some parts o version ietf-03 : September 2015, answer to comments from Phil Eardley * Improved introduction * Added details about using SOCKS and Korea Telecom's use-case in Section 2.3. * Added issue around clients caching DNS-results in Section 3.9 * Explained issue of MPTCP with stateless webservers Section 3.11 * Added description of MPTCP's use behind layer-4 loadbalancers Section 3.12 * Restructured text and improved writing in some parts o version ietf-04 : April 2016, answer to last comments * Updated text on measurements with smartphones * Updated conclusion Bonaventure, et al. Expires March 2, 2017 [Page 33] Internet-Draft MPTCP Experience August 2016 o version ietf-06 : August 2016, answer to AD's review * removed some expired drafts * removed conclusion Bonaventure, et al. Expires March 2, 2017 [Page 34] Internet-Draft MPTCP Experience August 2016 Authors' Addresses Olivier Bonaventure UCLouvain Email: Olivier.Bonaventure@uclouvain.be Christoph Paasch Apple, Inc. Email: cpaasch@apple.com Gregory Detal Tessares Email: Gregory.Detal@tessares.net Bonaventure, et al. Expires March 2, 2017 [Page 35]