Network Working Group F. Templin, Ed. Internet-Draft Boeing Research & Technology Obsoletes: rfc5320, rfc5558, rfc5720, July 27, 2016 rfc6179, rfc6706 (if approved) Intended status: Standards Track Expires: January 28, 2017 Asymmetric Extended Route Optimization (AERO) draft-templin-aerolink-70.txt Abstract This document specifies the operation of IP over tunnel virtual links using Asymmetric Extended Route Optimization (AERO). Nodes attached to AERO links can exchange packets via trusted intermediate routers that provide forwarding services to reach off-link destinations and redirection services for route optimization. AERO provides an IPv6 link-local address format known as the AERO address that supports operation of the IPv6 Neighbor Discovery (ND) protocol and links IPv6 ND to IP forwarding. Admission control, address/prefix provisioning and mobility are supported by the Dynamic Host Configuration Protocol for IPv6 (DHCPv6), and route optimization is naturally supported through dynamic neighbor cache updates. Although DHCPv6 and IPv6 ND messaging are used in the control plane, both IPv4 and IPv6 are supported in the data plane. AERO is a widely-applicable tunneling solution using standard control messaging exchanges as described in this document. Status of This Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at http://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." This Internet-Draft will expire on January 28, 2017. Templin Expires January 28, 2017 [Page 1] Internet-Draft AERO July 2016 Copyright Notice Copyright (c) 2016 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3 2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 4 3. Asymmetric Extended Route Optimization (AERO) . . . . . . . . 6 3.1. AERO Link Reference Model . . . . . . . . . . . . . . . . 6 3.2. AERO Link Node Types . . . . . . . . . . . . . . . . . . 8 3.3. AERO Addresses . . . . . . . . . . . . . . . . . . . . . 9 3.4. AERO Interface Characteristics . . . . . . . . . . . . . 10 3.5. AERO Link Registration . . . . . . . . . . . . . . . . . 11 3.6. AERO Interface Initialization . . . . . . . . . . . . . . 12 3.6.1. AERO Relay Behavior . . . . . . . . . . . . . . . . . 12 3.6.2. AERO Server Behavior . . . . . . . . . . . . . . . . 12 3.6.3. AERO Client Behavior . . . . . . . . . . . . . . . . 13 3.6.4. AERO Forwarding Agent Behavior . . . . . . . . . . . 13 3.7. AERO Routing System . . . . . . . . . . . . . . . . . . . 13 3.8. AERO Interface Neighbor Cache Maintenace . . . . . . . . 15 3.9. AERO Interface Sending Algorithm . . . . . . . . . . . . 16 3.10. AERO Interface Encapsulation and Re-encapsulation . . . . 18 3.11. AERO Interface Decapsulation . . . . . . . . . . . . . . 19 3.12. AERO Interface Data Origin Authentication . . . . . . . . 19 3.13. AERO Interface Packet Size Issues . . . . . . . . . . . . 20 3.14. AERO Interface Error Handling . . . . . . . . . . . . . . 22 3.15. AERO Router Discovery, Prefix Delegation and Address Configuration . . . . . . . . . . . . . . . . . . . . . . 25 3.15.1. AERO DHCPv6 Service Model . . . . . . . . . . . . . 25 3.15.2. AERO Client Behavior . . . . . . . . . . . . . . . . 25 3.15.3. AERO Server Behavior . . . . . . . . . . . . . . . . 28 3.15.4. Deleting Link Registrations . . . . . . . . . . . . 32 3.16. AERO Forwarding Agent Behavior . . . . . . . . . . . . . 32 3.17. AERO Intradomain Route Optimization . . . . . . . . . . . 33 3.17.1. Reference Operational Scenario . . . . . . . . . . . 33 3.17.2. Concept of Operations . . . . . . . . . . . . . . . 35 Templin Expires January 28, 2017 [Page 2] Internet-Draft AERO July 2016 3.17.3. Message Format . . . . . . . . . . . . . . . . . . . 35 3.17.4. Sending Predirects . . . . . . . . . . . . . . . . . 36 3.17.5. Re-encapsulating and Relaying Predirects . . . . . . 37 3.17.6. Processing Predirects and Sending Redirects . . . . 38 3.17.7. Re-encapsulating and Relaying Redirects . . . . . . 40 3.17.8. Processing Redirects . . . . . . . . . . . . . . . . 40 3.17.9. Server-Oriented Redirection . . . . . . . . . . . . 41 3.17.10. Route Optimization Policy . . . . . . . . . . . . . 41 3.17.11. Route Optimization and Multiple ACPs . . . . . . . . 42 3.18. Neighbor Unreachability Detection (NUD) . . . . . . . . . 42 3.19. Mobility Management . . . . . . . . . . . . . . . . . . . 43 3.19.1. Announcing Link-Layer Address Changes . . . . . . . 43 3.19.2. Bringing New Links Into Service . . . . . . . . . . 43 3.19.3. Removing Existing Links from Service . . . . . . . . 43 3.19.4. Moving to a New Server . . . . . . . . . . . . . . . 44 3.19.5. Packet Queueing for Mobility . . . . . . . . . . . . 44 3.20. Proxy AERO . . . . . . . . . . . . . . . . . . . . . . . 45 3.21. Extending AERO Links Through Security Gateways . . . . . 47 3.22. Extending IPv6 AERO Links to the Internet . . . . . . . . 49 3.23. Encapsulation Protocol Version Considerations . . . . . . 52 3.24. Multicast Considerations . . . . . . . . . . . . . . . . 53 3.25. Operation on AERO Links Without DHCPv6 Services . . . . . 53 3.26. Operation on Server-less AERO Links . . . . . . . . . . . 53 3.27. Manually-Configured AERO Tunnels . . . . . . . . . . . . 53 3.28. Intradomain Routing . . . . . . . . . . . . . . . . . . . 54 4. Implementation Status . . . . . . . . . . . . . . . . . . . . 54 5. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 54 6. Security Considerations . . . . . . . . . . . . . . . . . . . 54 7. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 55 8. References . . . . . . . . . . . . . . . . . . . . . . . . . 56 8.1. Normative References . . . . . . . . . . . . . . . . . . 56 8.2. Informative References . . . . . . . . . . . . . . . . . 58 Appendix A. AERO Alternate Encapsulations . . . . . . . . . . . 65 Appendix B. When to Insert an Encapsulation Fragment Header . . 66 Author's Address . . . . . . . . . . . . . . . . . . . . . . . . 67 1. Introduction This document specifies the operation of IP over tunnel virtual links using Asymmetric Extended Route Optimization (AERO). The AERO link can be used for tunneling to neighboring nodes over either IPv6 or IPv4 networks, i.e., AERO views the IPv6 and IPv4 networks as equivalent links for tunneling. Nodes attached to AERO links can exchange packets via trusted intermediate routers that provide forwarding services to reach off-link destinations and redirection services for route optimization [RFC5522]. Templin Expires January 28, 2017 [Page 3] Internet-Draft AERO July 2016 AERO provides an IPv6 link-local address format known as the AERO address that supports operation of the IPv6 Neighbor Discovery (ND) [RFC4861] protocol and links IPv6 ND to IP forwarding. Admission control, address/prefix provisioning and mobility are supported by the Dynamic Host Configuration Protocol for IPv6 (DHCPv6) [RFC3315], and route optimization is naturally supported through dynamic neighbor cache updates. Although DHCPv6 and IPv6 ND messaging are used in the control plane, both IPv4 and IPv6 can be used in the data plane. AERO is a widely-applicable tunneling solution using standard control messaging exchanges as described in this document. The remainder of this document presents the AERO specification. 2. Terminology The terminology in the normative references applies; the following terms are defined within the scope of this document: AERO link a Non-Broadcast, Multiple Access (NBMA) tunnel virtual overlay configured over a node's attached IPv6 and/or IPv4 networks. All nodes on the AERO link appear as single-hop neighbors from the perspective of the virtual overlay even though they may be separated by many underlying network hops. AERO can also operate over native multiple access link types (e.g., Ethernet, WiFi etc.) when a tunnel virtual overlay is not needed. AERO interface a node's attachment to an AERO link. Nodes typically have a single AERO interface; support for multiple AERO interfaces is also possible but out of scope for this document. AERO interfaces do not require Duplicate Address Detection (DAD) and therefore set the administrative variable DupAddrDetectTransmits to zero [RFC4862]. AERO address an IPv6 link-local address constructed as specified in Section 3.3 and assigned to a Client's AERO interface. AERO node a node that is connected to an AERO link and that participates in IPv6 ND and DHCPv6 messaging over the link. AERO Client ("Client") a node that issues DHCPv6 messages to receive IP Prefix Delegations (PDs) from one or more AERO Servers. Following PD, the Client assigns an AERO address to the AERO interface for use in DHCPv6 and IPv6 ND exchanges with other AERO nodes. Templin Expires January 28, 2017 [Page 4] Internet-Draft AERO July 2016 AERO Server ("Server") a node that configures an AERO interface to provide default forwarding and DHCPv6 services for AERO Clients. The Server assigns an administratively provisioned IPv6 link-local unicast address to support the operation of DHCPv6 and the IPv6 ND protocol. An AERO Server can also act as an AERO Relay. AERO Relay ("Relay") a node that configures an AERO interface to relay IP packets between nodes on the same AERO link and/or forward IP packets between the AERO link and the native Internetwork. The Relay assigns an administratively provisioned IPv6 link-local unicast address to the AERO interface the same as for a Server. An AERO Relay can also act as an AERO Server. AERO Forwarding Agent ("Forwarding Agent") a node that performs data plane forwarding services as a companion to an AERO Server. ingress tunnel endpoint (ITE) an AERO interface endpoint that injects tunneled packets into an AERO link. egress tunnel endpoint (ETE) an AERO interface endpoint that receives tunneled packets from an AERO link. underlying network a connected IPv6 or IPv4 network routing region over which the tunnel virtual overlay is configured. A typical example is an enterprise network, but many other use cases are also in scope. underlying interface an AERO node's interface point of attachment to an underlying network. link-layer address an IP address assigned to an AERO node's underlying interface. When UDP encapsulation is used, the UDP port number is also considered as part of the link-layer address; otherwise, UDP port number is set to the constant value '0'. Link-layer addresses are used as the encapsulation header source and destination addresses. network layer address the source or destination address of the encapsulated IP packet. end user network (EUN) Templin Expires January 28, 2017 [Page 5] Internet-Draft AERO July 2016 an internal virtual or external edge IP network that an AERO Client connects to the rest of the network via the AERO interface. AERO Service Prefix (ASP) an IP prefix associated with the AERO link and from which AERO Client Prefixes (ACPs) are derived (for example, the IPv6 ACP 2001:db8:1:2::/64 is derived from the IPv6 ASP 2001:db8::/32). AERO Client Prefix (ACP) a more-specific IP prefix taken from an ASP and delegated to a Client. Throughout the document, the simple terms "Client", "Server" and "Relay" refer to "AERO Client", "AERO Server" and "AERO Relay", respectively. Capitalization is used to distinguish these terms from DHCPv6 client/server/relay [RFC3315]. The terminology of DHCPv6 [RFC3315] and IPv6 ND [RFC4861] (including the names of node variables and protocol constants) applies to this document. Also throughout the document, the term "IP" is used to generically refer to either Internet Protocol version (i.e., IPv4 or IPv6). The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [RFC2119]. Lower case uses of these words are not to be interpreted as carrying RFC2119 significance. 3. Asymmetric Extended Route Optimization (AERO) The following sections specify the operation of IP over Asymmetric Extended Route Optimization (AERO) links: 3.1. AERO Link Reference Model Templin Expires January 28, 2017 [Page 6] Internet-Draft AERO July 2016 .-(::::::::) .-(:::: IP ::::)-. (:: Internetwork ::) `-(::::::::::::)-' `-(::::::)-' | +--------------+ +--------+-------+ +--------------+ |AERO Server S1| | AERO Relay R1 | |AERO Server S2| | Nbr: C1; R1 | | Nbr: S1; S2 | | Nbr: C2; R1 | | default->R1 | |(P1->S1; P2->S2)| | default->R1 | | P1->C1 | | ASP A1 | | P2->C2 | +-------+------+ +--------+-------+ +------+-------+ | | | X---+---+-------------------+------------------+---+---X | AERO Link | +-----+--------+ +--------+-----+ |AERO Client C1| |AERO Client C2| | Nbr: S1 | | Nbr: S2 | | default->S1 | | default->S2 | | ACP P1 | | ACP P2 | +--------------+ +--------------+ .-. .-. ,-( _)-. ,-( _)-. .-(_ IP )-. .-(_ IP )-. (__ EUN ) (__ EUN ) `-(______)-' `-(______)-' | | +--------+ +--------+ | Host H1| | Host H2| +--------+ +--------+ Figure 1: AERO Link Reference Model Figure 1 presents the AERO link reference model. In this model: o AERO Relay R1 aggregates AERO Service Prefix (ASP) A1, acts as a default router for its associated Servers S1 and S2, and connects the AERO link to the rest of the IP Internetwork. o AERO Servers S1 and S2 associate with Relay R1 and also act as default routers for their associated Clients C1 and C2. o AERO Clients C1 and C2 associate with Servers S1 and S2, respectively. They receive AERO Client Prefix (ACP) delegations P1 and P2, and also act as default routers for their associated physical or internal virtual EUNs. (Alternatively, clients can act as multi-addressed hosts without serving any EUNs). Templin Expires January 28, 2017 [Page 7] Internet-Draft AERO July 2016 o Simple hosts H1 and H2 attach to the EUNs served by Clients C1 and C2, respectively. Each AERO node maintains an AERO interface neighbor cache and an IP forwarding table. For example, AERO Relay R1 in the diagram has neighbor cache entries for Servers S1 and S2 as well as IP forwarding table entries for the ACPs delegated to Clients C1 and C2. In common operational practice, there may be many additional Relays, Servers and Clients. (Although not shown in the figure, AERO Forwarding Agents may also be provided for data plane forwarding offload services.) 3.2. AERO Link Node Types AERO Relays provide default forwarding services to AERO Servers. Relays forward packets between neighbors connected to the same AERO link and also forward packets between the AERO link and the native IP Internetwork. Relays present the AERO link to the native Internetwork as a set of one or more AERO Service Prefixes (ASPs) and serve as a gateway between the AERO link and the Internetwork. AERO Relays maintain an AERO interface neighbor cache entry for each AERO Server, and maintain an IP forwarding table entry for each AERO Client Prefix (ACP). AERO Relays can also be configured to act as AERO Servers. AERO Servers provide default forwarding services to AERO Clients. Each Server also peers with each Relay in a dynamic routing protocol instance to advertise its list of associated ACPs. Servers configure a DHCPv6 server function to facilitate Prefix Delegation (PD) exchanges with Clients. Each delegated prefix becomes an ACP taken from an ASP. Servers forward packets between AERO interface neighbors, and maintain an AERO interface neighbor cache entry for each AERO Relay. They also maintain both neighbor cache entries and IP forwarding table entries for each of their associated Clients. AERO Servers can also be configured to act as AERO Relays. AERO Clients act as requesting routers to receive ACPs through DHCPv6 PD exchanges with AERO Servers over the AERO link. Each Client MAY associate with a single Server or with multiple Servers, e.g., for fault tolerance, load balancing, etc. Each IPv6 Client receives at least a /64 IPv6 ACP, and may receive even shorter prefixes. Similarly, each IPv4 Client receives at least a /32 IPv4 ACP (i.e., a singleton IPv4 address), and may receive even shorter prefixes. AERO Clients maintain an AERO interface neighbor cache entry for each of their associated Servers as well as for each of their correspondent Clients. Templin Expires January 28, 2017 [Page 8] Internet-Draft AERO July 2016 AERO Forwarding Agents provide data plane forwarding services as companions to AERO Servers. Note that while Servers are required to perform both control and data plane operations on their own behalf, they may optionally enlist the services of special-purpose Forwarding Agents to offload data plane traffic. 3.3. AERO Addresses An AERO address is an IPv6 link-local address with an embedded ACP and assigned to a Client's AERO interface. The AERO address is formed as follows: fe80::[ACP] For IPv6, the AERO address begins with the prefix fe80::/64 and includes in its interface identifier the base prefix taken from the Client's IPv6 ACP. The base prefix is determined by masking the ACP with the prefix length. For example, if the AERO Client receives the IPv6 ACP: 2001:db8:1000:2000::/56 it constructs its AERO address as: fe80::2001:db8:1000:2000 For IPv4, the AERO address is formed from the lower 64 bits of an IPv4-mapped IPv6 address [RFC4291] that includes the base prefix taken from the Client's IPv4 ACP. For example, if the AERO Client receives the IPv4 ACP: 192.0.2.32/28 it constructs its AERO address as: fe80::FFFF:192.0.2.32 The AERO address remains stable as the Client moves between topological locations, i.e., even if its link-layer addresses change. NOTE: In some cases, prospective neighbors may not have advanced knowledge of the Client's ACP length and may therefore send initial IPv6 ND messages with an AERO destination address that matches the ACP but does not correspond to the base prefix. For example, if the Client receives the IPv6 ACP 2001:db8:1000:2000::/56 then subsequently receives an IPv6 ND message with destination address fe80::2001:db8:1000:2001, it accepts the message as though it were addressed to fe80::2001:db8:1000:2000. Templin Expires January 28, 2017 [Page 9] Internet-Draft AERO July 2016 3.4. AERO Interface Characteristics AERO interfaces use encapsulation (see: Section 3.10) to exchange packets with neighbors attached to the AERO link. AERO interfaces maintain a neighbor cache, and AERO nodes use both DHCPv6 PD and IPv6 ND control messaging. AERO Clients send DHCPv6 Solicit, Rebind, Renew and Release messages to AERO Servers, which respond with DHCPv6 Reply messages. These messages result in the creation, modification and deletion of neighbor cache entries. AERO interfaces use unicast IPv6 ND Neighbor Solicitation (NS), Neighbor Advertisement (NA), Router Solicitation (RS) and Router Advertisement (RA) messages the same as for any IPv6 link. AERO interfaces use two IPv6 ND redirection message types -- the first known as a Predirect message and the second being the standard Redirect message (see Section 3.17). AERO links further use link- local-only addressing; hence, AERO nodes ignore any Prefix Information Options (PIOs) they may receive in RA messages over an AERO interface. AERO interface ND messages include one or more Source/Target Link- Layer Address Options (S/TLLAOs) formatted as shown in Figure 2: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type = 2 | Length = 3 | Reserved | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Link ID | NDSCPs | DSCP #1 |Prf| DSCP #2 |Prf| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | DSCP #3 |Prf| DSCP #4 |Prf| .... +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | UDP Port Number | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + | | + + | IP Address | + + | | + +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 2: AERO Source/Target Link-Layer Address Option (S/TLLAO) Format In this format, Link ID is an integer value between 0 and 255 corresponding to an underlying interface of the target node, NDSCPs Templin Expires January 28, 2017 [Page 10] Internet-Draft AERO July 2016 encodes an integer value between 0 and 64 indicating the number of Differentiated Services Code Point (DSCP) octets that follow. Each DSCP octet is a 6-bit integer DSCP value followed by a 2-bit Preference ("Prf") value. Each DSCP value encodes an integer between 0 and 63 associated with this Link ID, where the value 0 means "default" and other values are interpreted as specified in [RFC2474]. The 'Prf' qualifier for each DSCP value is set to the value 0 ("deprecated'), 1 ("low"), 2 ("medium"), or 3 ("high") to indicate a preference level for packet forwarding purposes. When a particular DSCP value is not specified, its preference level is set to "medium" by default. UDP Port Number and IP Address are set to the addresses used by the target node when it sends encapsulated packets over the underlying interface. When UDP is not used as part of the encapsulation, UDP Port Number is set to the value '0'. When the encapsulation IP address family is IPv4, IP Address is formed as an IPv4-mapped IPv6 address [RFC4291]. AERO interfaces may be configured over multiple underlying interfaces. For example, common mobile handheld devices have both wireless local area network ("WLAN") and cellular wireless links. These links are typically used "one at a time" with low-cost WLAN preferred and highly-available cellular wireless as a standby. In a more complex example, aircraft frequently have many wireless data link types (e.g. satellite-based, terrestrial, air-to-air directional, etc.) with diverse performance and cost properties. If a Client's multiple underlying interfaces are used "one at a time" (i.e., all other interfaces are in standby mode while one interface is active), then Redirect, Predirect and unsolicited NA messages include only a single TLLAO with Link ID set to a constant value. If the Client has multiple active underlying interfaces, then from the perspective of IPv6 ND it would appear to have multiple link- layer addresses. In that case, Redirect and Predirect messages MAY include multiple TLLAOs -- each with a Link ID that corresponds to a specific underlying interface of the Client. 3.5. AERO Link Registration When an administrative authority first deploys a set of AERO Relays and Servers that comprise an AERO link, they also assign a unique domain name for the link, e.g., "linkupnetworks.example.com". Next, if administrative policy permits Clients within the domain to serve as correspondent nodes for Internet mobile nodes, the administrative authority adds a Fully Qualified Domain Name (FQDN) for each of the AERO link's ASPs to the Domain Name System (DNS) [RFC1035]. The FQDN Templin Expires January 28, 2017 [Page 11] Internet-Draft AERO July 2016 is based on the suffix "aero.linkupnetworks.net" with a prefix formed from the wildcard-terminated reverse mapping of the ASP [RFC3596][RFC4592], and resolves to a DNS PTR resource record. For example, for the ASP '2001:db8:1::/48' within the domain name "linkupnetworks.example.com", the DNS database contains: '*.1.0.0.0.8.b.d.0.1.0.0.2.aero.linkupnetworks.net. PTR linkupnetworks.example.com' This DNS registration advertises the AERO link's ASPs to prospective correspondent nodes. 3.6. AERO Interface Initialization 3.6.1. AERO Relay Behavior When a Relay enables an AERO interface, it first assigns an administratively provisioned link-local address fe80::ID to the interface. Each fe80::ID address MUST be unique among all AERO nodes on the link, and MUST NOT collide with any potential AERO addresses nor the special addresses fe80:: and fe80::ffff:ffff:ffff:ffff. (The fe80::ID addresses are typically taken from the available range fe80::/96, e.g., as fe80::1, fe80::2, fe80::3, etc.) The Relay then engages in a dynamic routing protocol session with all Servers on the link (see: Section 3.7), and advertises its assigned ASP prefixes into the native IP Internetwork. Each Relay subsequently maintains an IP forwarding table entry for each ACP covered by its ASP(s), and maintains a neighbor cache entry for each Server on the link. Relays exchange NS/NA messages with AERO link neighbors the same as for any AERO node, however they typically do not perform explicit Neighbor Unreachability Detection (NUD) (see: Section 3.18) since the dynamic routing protocol already provides reachability confirmation. 3.6.2. AERO Server Behavior When a Server enables an AERO interface, it assigns an administratively provisioned link-local address fe80::ID the same as for Relays. The Server further configures a DHCPv6 server function to facilitate DHCPv6 PD exchanges with AERO Clients. The Server maintains a neighbor cache entry for each Relay on the link, and manages per-ACP neighbor cache entries and IP forwarding table entries based on control message exchanges. Each Server also engages in a dynamic routing protocol with each Relay on the link (see: Section 3.7). Templin Expires January 28, 2017 [Page 12] Internet-Draft AERO July 2016 When the Server receives an NS/RS message from a Client on the AERO interface it returns an NA/RA message. The Server further provides a simple link-layer conduit between AERO interface neighbors. Therefore, packets enter the Server's AERO interface from the link layer and are forwarded back out the link layer without ever leaving the AERO interface and therefore without ever disturbing the network layer. 3.6.3. AERO Client Behavior When a Client enables an AERO interface, it uses the special address fe80::ffff:ffff:ffff:ffff to obtain one or more ACPs from an AERO Server via DHCPv6 PD. Next, it assigns the corresponding AERO address(es) to the AERO interface and creates a neighbor cache entry for the Server, i.e., the DHCPv6 PD exchange bootstraps autoconfiguration of unique link-local address(es). The Client maintains a neighbor cache entry for each of its Servers and each of its active correspondent Clients. When the Client receives Redirect/ Predirect messages on the AERO interface it updates or creates neighbor cache entries, including link-layer address information. 3.6.4. AERO Forwarding Agent Behavior When a Forwarding Agent enables an AERO interface, it assigns the same link-local address(es) as the companion AERO Server. The Forwarding Agent thereafter provides data plane forwarding services based solely on the forwarding information assigned to it by the companion AERO Server. 3.7. AERO Routing System The AERO routing system is based on a private instance of the Border Gateway Protocol (BGP) [RFC4271] that is coordinated between Relays and Servers and does not interact with either the public Internet BGP routing system or the native IP Internetwork interior routing system. Relays advertise only a small and unchanging set of ASPs to the native routing system instead of the full dynamically changing set of ACPs. In a reference deployment, each AERO Server is configured as an Autonomous System Border Router (ASBR) for a stub Autonomous System (AS) using an AS Number (ASN) that is unique within the BGP instance, and each Server further peers with each Relay but does not peer with other Servers. Similarly, Relays do not peer with each other, since they will reliably receive all updates from all Servers and will therefore have a consistent view of the AERO link ACP delegations. Templin Expires January 28, 2017 [Page 13] Internet-Draft AERO July 2016 Each Server maintains a working set of associated ACPs, and dynamically announces new ACPs and withdraws departed ACPs in its BGP updates to Relays. Clients are expected to remain associated with their current Servers for extended timeframes, however Servers SHOULD selectively suppress BGP updates for impatient Clients that repeatedly associate and disassociate with them in order to dampen routing churn. Each Relay configures a black-hole route for each of its ASPs. By black-holing the ASPs, the Relay will maintain forwarding table entries only for the ACPs that are currently active, and all other ACPs will correctly result in destination unreachable failures due to the black hole route. Scaling properties of the AERO routing system are limited by the number of BGP routes that can be carried by Relays. Assuming O(10^6) as a reasonable maximum number of BGP routes, this means that O(10^6) Clients can be serviced by a single set of Relays. A means of increasing scaling would be to assign a different set of Relays for each set of ASPs. In that case, each Server still peers with each Relay, but the Server institutes route filters so that each set of Relays only receives BGP updates for the ASPs they aggregate. For example, if the ASP for the AERO link is 2001:db8::/32, a first set of Relays could service the ASP segment 2001:db8::/40, a second set of Relays could service 2001:db8:0100::/40, a third set could service 2001:db8:0200::/40, etc. Assuming up to O(10^3) sets of Relays, the AERO routing system can then accommodate O(10^9) ACPs with no additional overhead for Servers and Relays (for example, it should be possible to service 4 billion /64 ACPs taken from a /32 ASP and even more for shorter ASPs). In this way, each set of Relays services a specific set of ASPs that they advertise to the native routing system, and each Server configures ASP-specific routes that list the correct set of Relays as next hops. This arrangement also allows for natural incremental deployment, and can support small scale initial deployments followed by dynamic deployment of additional Clients, Servers and Relays without disturbing the already-deployed base. Note that in an alternate routing arrangement each set of Relays could advertise the aggregated ASP for the link into the native routing system even though each Relay services only a segment of the ASP. In that case, a Relay upon receiving a packet with a destination address covered by the ASP segment of another Relay can simply tunnel the packet to the correct Relay. The tradeoff then is the penalty for Relay-to-Relay tunneling compared with reduced routing information in the native routing system. Templin Expires January 28, 2017 [Page 14] Internet-Draft AERO July 2016 3.8. AERO Interface Neighbor Cache Maintenace Each AERO interface maintains a conceptual neighbor cache that includes an entry for each neighbor it communicates with on the AERO link, the same as for any IPv6 interface [RFC4861]. AERO interface neighbor cache entires are said to be one of "permanent", "static" or "dynamic". Permanent neighbor cache entries are created through explicit administrative action; they have no timeout values and remain in place until explicitly deleted. AERO Relays maintain a permanent neighbor cache entry for each Server on the link, and AERO Servers maintain a permanent neighbor cache entry for each Relay. Each entry maintains the mapping between the neighbor's fe80::ID network-layer address and corresponding link-layer address. Static neighbor cache entries are created through DHCPv6 PD exchanges and remain in place for durations bounded by prefix lifetimes. AERO Servers maintain static neighbor cache entries for the ACPs of each of their associated Clients, and AERO Clients maintain a static neighbor cache entry for each of their associated Servers. When an AERO Server sends a Reply message response to a Client's Solicit, Rebind or Renew message, it creates or updates a static neighbor cache entry based on the Client's DHCP Unique Identifier (DUID) as the Client identifier, the AERO address(es) corresponding to the Client's ACP(s) as the network-layer address(es), the prefix lifetime as the neighbor cache entry lifetime, the Client's encapsulation IP address and UDP port number as the link-layer address and the prefix length(s) as the length to apply to the AERO address(es). When an AERO Client receives a Reply message from a Server, it creates or updates a static neighbor cache entry based on the Reply message link-local source address as the network-layer address, the prefix lifetime as the neighbor cache entry lifetime, and the encapsulation IP source address and UDP source port number as the link-layer address. Dynamic neighbor cache entries are created or updated based on receipt of a Predirect/Redirect message, and are garbage-collected if not used within a bounded timescale. AERO Clients maintain dynamic neighbor cache entries for each of their active correspondent Client ACPs with lifetimes based on IPv6 ND messaging constants. When an AERO Client receives a valid Predirect message it creates or updates a dynamic neighbor cache entry for the Predirect target network-layer and link-layer addresses plus prefix length. The node then sets an "AcceptTime" variable in the neighbor cache entry to ACCEPT_TIME seconds and uses this value to determine whether packets received from the correspondent can be accepted. When an AERO Client receives a valid Redirect message it creates or updates a dynamic neighbor Templin Expires January 28, 2017 [Page 15] Internet-Draft AERO July 2016 cache entry for the Redirect target network-layer and link-layer addresses plus prefix length. The Client then sets a "ForwardTime" variable in the neighbor cache entry to FORWARD_TIME seconds and uses this value to determine whether packets can be sent directly to the correspondent. The Client also sets a "MaxRetry" variable to MAX_RETRY to limit the number of keepalives sent when a correspondent may have gone unreachable. It is RECOMMENDED that FORWARD_TIME be set to the default constant value 30 seconds to match the default REACHABLE_TIME value specified for IPv6 ND [RFC4861]. It is RECOMMENDED that ACCEPT_TIME be set to the default constant value 40 seconds to allow a 10 second window so that the AERO redirection procedure can converge before AcceptTime decrements below FORWARD_TIME. It is RECOMMENDED that MAX_RETRY be set to 3 the same as described for IPv6 ND address resolution in Section 7.3.3 of [RFC4861]. Different values for FORWARD_TIME, ACCEPT_TIME, and MAX_RETRY MAY be administratively set, if necessary, to better match the AERO link's performance characteristics; however, if different values are chosen, all nodes on the link MUST consistently configure the same values. Most importantly, ACCEPT_TIME SHOULD be set to a value that is sufficiently longer than FORWARD_TIME to allow the AERO redirection procedure to converge. When there may be a Network Address Translator (NAT) between the Client and the Server, or if the path from the Client to the Server should be tested for reachability, the Client can send periodic RS messages to the Server to receive RA replies. The RS/RA messaging will keep NAT state alive and test Server reachability without disturbing the DHCPv6 server. 3.9. AERO Interface Sending Algorithm IP packets enter a node's AERO interface either from the network layer (i.e., from a local application or the IP forwarding system), or from the link layer (i.e., from the AERO tunnel virtual link). Packets that enter the AERO interface from the network layer are encapsulated and admitted into the AERO link, i.e., they are tunnelled to an AERO interface neighbor. Packets that enter the AERO interface from the link layer are either re-admitted into the AERO link or delivered to the network layer where they are subject to either local delivery or IP forwarding. Since each AERO node may have only partial information about neighbors on the link, AERO interfaces may forward packets with link-local destination addresses Templin Expires January 28, 2017 [Page 16] Internet-Draft AERO July 2016 at a layer below the network layer. This means that AERO nodes act as both IP routers/hosts and sub-IP layer forwarding nodes. AERO interface sending considerations for Clients, Servers and Relays are given below. When an IP packet enters a Client's AERO interface from the network layer, if the destination is covered by an ASP the Client searches for a dynamic neighbor cache entry with a non-zero ForwardTime and an AERO address that matches the packet's destination address. (The destination address may be either an address covered by the neighbor's ACP or the (link-local) AERO address itself.) If there is a match, the Client uses a link-layer address in the entry as the link-layer address for encapsulation then admits the packet into the AERO link. If there is no match, the Client instead uses the link- layer address of a neighboring Server as the link-layer address for encapsulation. When an IP packet enters a Server's AERO interface from the link layer, if the destination is covered by an ASP the Server searches for a neighbor cache entry with an AERO address that matches the packet's destination address. (The destination address may be either an address covered by the neighbor's ACP or the AERO address itself.) If there is a match, the Server uses a link-layer address in the entry as the link-layer address for encapsulation and re-admits the packet into the AERO link. If there is no match, the Server instead uses the link-layer address in a permanent neighbor cache entry for a Relay selected through longest-prefix-match as the link-layer address for encapsulation. When an IP packet enters a Relay's AERO interface from the network layer, the Relay searches its IP forwarding table for an entry that is covered by an ASP and also matches the destination. If there is a match, the Relay uses the link-layer address in the corresponding neighbor cache entry as the link-layer address for encapsulation and admits the packet into the AERO link. When an IP packet enters a Relay's AERO interface from the link-layer, if the destination is not a link-local address and does not match an ASP the Relay removes the packet from the AERO interface and uses IP forwarding to forward the packet to the Internetwork. If the destination address is a link- local address or a non-link-local address that matches an ASP, and there is a more-specific ACP entry in the IP forwarding table, the Relay uses the link-layer address in the corresponding neighbor cache entry as the link-layer address for encapsulation and re-admits the packet into the AERO link. When an IP packet enters a Relay's AERO interface from either the network layer or link-layer, and the packet's destination address matches an ASP but there is no more- specific ACP entry, the Relay drops the packet and returns an ICMP Destination Unreachable message (see: Section 3.14). Templin Expires January 28, 2017 [Page 17] Internet-Draft AERO July 2016 When an AERO Server receives a packet from a Relay via the AERO interface, the Server MUST NOT forward the packet back to the same or a different Relay. When an AERO Relay receives a packet from a Server via the AERO interface, the Relay MUST NOT forward the packet back to the same Server. When an AERO node re-admits a packet into the AERO link without involving the network layer, the node MUST NOT decrement the network layer TTL/Hop-count. When an AERO node forwards a data packet to the primary link-layer address of a Server, it may receive Redirect messages with an SLLAO that include the link-layer address of an AERO Forwarding Agent. The AERO node SHOULD record the link-layer address in the neighbor cache entry for the neighbor and send subsequent data packets via this address instead of the Server's primary address (see: Section 3.16). 3.10. AERO Interface Encapsulation and Re-encapsulation AERO interfaces encapsulate IP packets according to whether they are entering the AERO interface from the network layer or if they are being re-admitted into the same AERO link they arrived on. This latter form of encapsulation is known as "re-encapsulation". The AERO interface encapsulates packets per the Generic UDP Encapsulation (GUE) encapsulation procedures in [I-D.ietf-nvo3-gue][I-D.herbert-gue-fragmentation], or through an alternate encapsulation format (see: Appendix A). For packets entering the AERO link from the IP layer, the AERO interface copies the "TTL/Hop Limit", "Type of Service/Traffic Class" [RFC2983], "Flow Label"[RFC6438].(for IPv6) and "Congestion Experienced" [RFC3168] values in the packet's IP header into the corresponding fields in the encapsulation IP header. For packets undergoing re-encapsulation within the AERO link, the AERO interface instead copies the "TTL/Hop Limit", "Type of Service/Traffic Class", "Flow Label" and "Congestion Experienced" values in the original encapsulation IP header into the corresponding fields in the new encapsulation IP header, i.e., the values are transferred between encapsulation headers and *not* copied from the encapsulated packet's network-layer header. When GUE encapsulation is used, the AERO interface next sets the UDP source port to a constant value that it will use in each successive packet it sends, and sets the UDP length field to the length of the encapsulated packet plus 8 bytes for the UDP header itself plus the length of the GUE header (or 0 if GUE direct IP encapsulation is used). For packets sent to a Server, the AERO interface sets the UDP Templin Expires January 28, 2017 [Page 18] Internet-Draft AERO July 2016 destination port to 8060, i.e., the IANA-registered port number for AERO. For packets sent to a correspondent Client, the AERO interface sets the UDP destination port to the port value stored in the neighbor cache entry for this correspondent. The AERO interface then either includes or omits the UDP checksum according to the GUE specification. For IPv4 encapsulation, the AERO interface sets the DF bit as discussed in Section 3.13. 3.11. AERO Interface Decapsulation AERO interfaces decapsulate packets destined either to the AERO node itself or to a destination reached via an interface other than the AERO interface the packet was received on. Decapsulation is per the procedures specified for the appropriate encapsulation format. 3.12. AERO Interface Data Origin Authentication AERO nodes employ simple data origin authentication procedures for encapsulated packets they receive from other nodes on the AERO link. In particular: o AERO Servers and Relays accept encapsulated packets with a link- layer source address that matches a permanent neighbor cache entry. o AERO Servers accept authentic encapsulated DHCPv6 messages from Clients, and create or update a static neighbor cache entry for the Client based on the specific DHCPv6 message type. o AERO Clients and Servers accept encapsulated packets if there is a static neighbor cache entry with a link-layer address that matches the packet's link-layer source address. o AERO Clients, Servers and Relays accept encapsulated packets if there is a dynamic neighbor cache entry with an AERO address that matches the packet's network-layer source address, with a link- layer address that matches the packet's link-layer source address, and with a non-zero AcceptTime. Note that this simple data origin authentication is effective in environments in which link-layer addresses cannot be spoofed. In other environments, each AERO message must include a signature that the recipient can use to authenticate the message origin. Templin Expires January 28, 2017 [Page 19] Internet-Draft AERO July 2016 3.13. AERO Interface Packet Size Issues The AERO interface is the node's attachment to the AERO link. The AERO interface acts as a tunnel ingress when it sends a packet to an AERO link neighbor and as a tunnel egress when it receives a packet from an AERO link neighbor. AERO interfaces observe the packet sizing considerations for tunnels discussed in [I-D.ietf-intarea-tunnels] and as specified below. IPv6 specifies a minimum link Maximum Transmission Unit (MTU) of 1280 bytes [RFC2460]. Although IPv4 specifies a smaller minimum link MTU of 68 bytes [RFC0791], AERO interfaces also observe the IPv6 minimum for IPv4 even if the packet may incur fragmentation in the network. IPv6 specifies a minimum Maximum Reassembly Unit (MRU) of 1500 bytes [RFC2460], while the minimum MRU for IPv4 is only 576 bytes [RFC1122] (note that IPv6 over IPv4 tunnels assume a larger MRU than the IPv4 minimum). Original sources expect that IP packets will either be delivered to the final destination or a suitable Packet Too Big (PTB) message returned. However, PTB messages may be crafted for malicious purposes such as denial of service, or lost in the network [RFC2923] resulting in failure of the IP Path MTU Discovery (PMTUD) mechanisms [RFC1191][RFC1981]. For these reasons, AERO links employ operational procedures that avoid all interactions with PMTUD. AERO Servers advertise an MTU that MUST be no smaller than 1280 bytes, MUST be no larger than the minimum MRU among all nodes on the AERO link minus the encapsulation overhead ("ENCAPS"), and SHOULD be no smaller than 1500 bytes. AERO Servers advertise a Maximum Fragment Unit (MFU) as the maximum size for the fragments of an encapsulated packet that require fragmentation. The MFU value MUST be no larger than 1280 bytes unless there is operational assurance that a larger size can traverse the link along all paths without fragmentation, and MUST be no larger than (MTU+ENCAPS). AERO Clients set the AERO interface MTU/MFU based on the values advertised by their Server, and configure an MRU large enough to reassemble packets up to (MTU+ENCAPS) bytes. All AERO nodes on the link MUST configure the same MTU/MFU values for reasons cited in [RFC3819][RFC4861], e.g., to support multicast. All AERO nodes on the link MUST configure a minimum MRU of (1500+ENCAPS) bytes, and SHOULD be capable of setting a larger MRU accoding to the Server's advertised MTU. Templin Expires January 28, 2017 [Page 20] Internet-Draft AERO July 2016 In accordnace with these requirements, the ingress accommodates packets of various sizes as follows: o First, for original IPv4 packets that are larger than the AERO interface MTU and with the DF bit set to 0, the ingress uses IPv4 fragmentation to break the packet into a minimum number of non- overlapping fragments where the first fragment is no larger than (MFU-ENCAPS) bytes and the remaining fragments are no larger than the first. o Next, for each original IP packet or fragment that is no larger than (MFU-ENCAPS) bytes, the ingress encapsulates the packet and admits it into the tunnel. For IPv4 AERO links, the ingress sets the Don't Fragment (DF) bit to 0 so that these packets will be delivered to the egress even if some fragmentation occurs in the network. o For all other original IP packets or fragments, if the packet is larger than the AERO interface MTU, the ingress drops the packet and returns a PTB message to the original source. Otherwise, the ingress encapsulates the packet and fragments the encapsulated packet into a minimum number of non-overlapping fragments where the first fragment is no larger than MFU bytes and the remaining fragments are no larger than the first. The ingress then admits the fragments into the tunnel, and for IPv4 sets the DF bit to 0 in the IP encapsulation header. These fragmented encapsulated packets will be delivered to the egress, which reassembles them into a whole packet. Several factors must be considered when fragmentation of the encapsulated packet is needed. For AERO links over IPv4, the IP ID field is only 16 bits in length, meaning that fragmentation at high data rates could result in data corruption due to reassembly misassociations [RFC6864][RFC4963]. For AERO links over both IPv4 and IPv6, studies have also shown that IP fragments are dropped unconditionally over some network paths [I-D.taylor-v6ops-fragdrop]. In environments where IP fragmentation issues could result in operational problems, the ingress SHOULD employ intermediate-layer fragmentation (see: [RFC2764] and [I-D.herbert-gue-fragmentation]) before appending the outer encapsulation headers to each fragment. Since the encapsulation fragment header reduces the room available for packet data, but the original source has no way to control its insertion, the ingress MUST include the fragment header length in the ENCAPS length even for packets in which the header is absent. Templin Expires January 28, 2017 [Page 21] Internet-Draft AERO July 2016 3.14. AERO Interface Error Handling When an AERO node admits encapsulated packets into the AERO interface, it may receive link-layer (L2) or network-layer (L3) error indications. An L2 error indication is an ICMP error message generated by a router on the path to the neighbor or by the neighbor itself. The message includes an IP header with the address of the node that generated the error as the source address and with the link-layer address of the AERO node as the destination address. The IP header is followed by an ICMP header that includes an error Type, Code and Checksum. Valid type values include "Destination Unreachable", "Time Exceeded" and "Parameter Problem" [RFC0792][RFC4443]. (AERO interfaces ignore all L2 IPv4 "Fragmentation Needed" and IPv6 "Packet Too Big" messages since they only emit packets that are guaranteed to be no larger than the IP minimum link MTU.) The ICMP header is followed by the leading portion of the packet that generated the error, also known as the "packet-in-error". For ICMPv6, [RFC4443] specifies that the packet-in-error includes: "As much of invoking packet as possible without the ICMPv6 packet exceeding the minimum IPv6 MTU" (i.e., no more than 1280 bytes). For ICMPv4, [RFC0792] specifies that the packet-in-error includes: "Internet Header + 64 bits of Original Data Datagram", however [RFC1812] Section 4.3.2.3 updates this specification by stating: "the ICMP datagram SHOULD contain as much of the original datagram as possible without the length of the ICMP datagram exceeding 576 bytes". The L2 error message format is shown in Figure 3: Templin Expires January 28, 2017 [Page 22] Internet-Draft AERO July 2016 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ ~ ~ | L2 IP Header of | | error message | ~ ~ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | L2 ICMP Header | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ --- ~ ~ P | IP and other encapsulation | a | headers of original L3 packet | c ~ ~ k +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ e ~ ~ t | IP header of | | original L3 packet | i ~ ~ n +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ ~ ~ e | Upper layer headers and | r | leading portion of body | r | of the original L3 packet | o ~ ~ r +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ --- Figure 3: AERO Interface L2 Error Message Format The AERO node rules for processing these L2 error messages is as follows: o When an AERO node receives an L2 Parameter Problem message, it processes the message the same as described as for ordinary ICMP errors in the normative references [RFC0792][RFC4443]. o When an AERO node receives persistent L2 IPv4 Time Exceeded messages, the IP ID field may be wrapping before earlier fragments have been processed. In that case, the node SHOULD begin including integrity checks and/or institute rate limits for subseqent packets. o When an AERO Client receives persistent L2 Destination Unreachable messages in response to tunneled packets that it sends to one of its dynamic neighbor correspondents, the Client SHOULD test the path to the correspondent using Neighbor Unreachability Detection (NUD) (see Section 3.18). If NUD fails, the Client SHOULD set ForwardTime for the corresponding dynamic neighbor cache entry to 0 and allow future packets destined to the correspondent to flow through a Server. Templin Expires January 28, 2017 [Page 23] Internet-Draft AERO July 2016 o When an AERO Client receives persistent L2 Destination Unreachable messages in response to tunneled packets that it sends to one of its static neighbor Servers, the Client SHOULD test the path to the Server using NUD. If NUD fails, the Client SHOULD delete the neighbor cache entry and attempt to associate with a new Server. o When an AERO Server receives persistent L2 Destination Unreachable messages in response to tunneled packets that it sends to one of its static neighbor Clients, the Server SHOULD test the path to the Client using NUD. If NUD fails, the Server SHOULD cancel the DHCPv6 PD for the Client's ACP, withdraw its route for the ACP from the AERO routing system and delete the neighbor cache entry (see Section 3.18 and Section 3.19). o When an AERO Relay or Server receives an L2 Destination Unreachable message in response to a tunneled packet that it sends to one of its permanent neighbors, it discards the message since the AERO routing system is likely in a temporary transitional state that will soon re-converge. In case of a prolonged outage, however, the AERO routing system will compensate for Relays or Servers that have fallen silent. When an AERO Relay receives an L3 packet for which the destination address is covered by an ASP, if there is no more-specific routing information for the destination the Relay drops the packet and returns an L3 Destination Unreachable message. The Relay first writes the IP source address of the original L3 packet as the destination address of the L3 Destination Unreachable message and determines the next hop to the destination. If the next hop is reached via the AERO interface, the Relay uses the IPv6 address "::" or the IPv4 address "0.0.0.0" as the IP source address of the L3 Destination Unreachable message and forwards the message to the next hop within the AERO interface. Otherwise, the Relay uses one of its non link-local addresses as the source address of the L3 Destination Unreachable message and forwards the message via a link outside the AERO interface. When an AERO node receives an encapsulated packet for which the reassembly buffer it too small, it drops the packet and returns an L3 Packet To Big (PTB) message. The node first writes the IP source address of the original L3 packet as the destination address of the L3 PTB message and determines the next hop to the destination. If the next hop is reached via the AERO interface, the node uses the IPv6 address "::" or the IPv4 address "0.0.0.0" as the IP source address of the L3 PTB message and forwards the message to the next hop within the AERO interface. Otherwise, the node uses one of its non link-local addresses as the source address of the L3 PTB message and forwards the message via a link outside the AERO interface. Templin Expires January 28, 2017 [Page 24] Internet-Draft AERO July 2016 When an AERO node receives any L3 error message via the AERO interface, it examines the destination address in the L3 IP header of the message. If the next hop toward the destination address of the error message is via the AERO interface, the node re-encapsulates and forwards the message to the next hop within the AERO interface. Otherwise, if the source address in the L3 IP header of the message is the IPv6 address "::" or the IPv4 address "0.0.0.0", the node writes one of its non link-local addresses as the source address of the L3 message and recalculates the IP and/or ICMP checksums. The node finally forwards the message via a link outside of the AERO interface. 3.15. AERO Router Discovery, Prefix Delegation and Address Configuration 3.15.1. AERO DHCPv6 Service Model Each AERO Server configures a DHCPv6 server function to facilitate PD requests from Clients. Each Server is provisioned with a database of ACP-to-Client ID mappings for all Clients enrolled in the AERO system, as well as any information necessary to authenticate each Client. The Client database is maintained by a central administrative authority for the AERO link and securely distributed to all Servers, e.g., via the Lightweight Directory Access Protocol (LDAP) [RFC4511] or a similar distributed database service. Therefore, no Server-to-Server DHCPv6 PD delegation state synchronization is necessary, and Clients can optionally hold separate delegations for the same ACPs from multiple Servers. In this way, Clients can associate with multiple Servers, and can receive new delegations from new Servers before deprecating delegations received from existing Servers. This provides the Client with a natural fault-tolerance and/or load balancing profile. AERO Clients and Servers exchange Client link-layer address information using an option format similar to the Client Link Layer Address Option (CLLAO) defined in [RFC6939]. Due to practical limitations of CLLAO, however, AERO interfaces instead use Vendor- Specific Information Options as described in the following sections. 3.15.2. AERO Client Behavior AERO Clients discover the link-layer addresses of AERO Servers via static configuration (e.g., from a flat-file map of Server addresses and locations), or through an automated means such as DNS name resolution. In the absence of other information, the Client resolves the FQDN "linkupnetworks.[domainname]" where "linkupnetworks" is a constant text string and "[domainname]" is a DNS suffix for the Templin Expires January 28, 2017 [Page 25] Internet-Draft AERO July 2016 Client's underlying network (e.g., "example.com"). After discovering the link-layer addresses, the Client associates with one or more of the corresponding Servers. To associate with a Server, the Client acts as a requesting router to request ACPs through a two-message (i.e., Solicit/Reply) DHCPv6 PD exchange [RFC3315][RFC3633]. The Client's Solicit message includes fe80::ffff:ffff:ffff:ffff as the IPv6 source address, 'All_DHCP_Relay_Agents_and_Servers' as the IPv6 destination address and the link-layer address of the Server as the link-layer destination address. The Solicit message also includes a Client Identifier option with a DUID and an Identity Association for Prefix Delegation (IA_PD) option. If the Client is pre-provisioned with ACPs associated with the AERO service, it MAY also include the ACPs in the IA_PD to indicate its preferences to the DHCPv6 server. The Client also SHOULD include an AERO Link-registration Request (ALREQ) option in the Solicit message to register one or more links with the Server. The Server will include an AERO Link-registration Reply (ALREP) option in the corresponding Reply message as specified in Section 3.15.3. (The Client MAY omit the ALREQ option, in which case the Server will still include an ALREP option in its Reply with "Link ID" set to 0.) The format for the ALREQ option is shown in Figure 4: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | OPTION_VENDOR_OPTS | option-len (1) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | enterprise-number = 45282 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | opt-code = OPTION_ALREQ (0) | option-len (2) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Link ID | DSCP #1 |Prf| DSCP #2 |Prf| ... +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+- Figure 4: AERO Link-registration Request (ALREQ) Option In the above format, the Client sets 'option-code' to OPTION_VENDOR_OPTS, sets 'option-len (1)' to the length of the option following this field, sets 'enterprise-number' to 45282 (see: "IANA Considerations"), sets opt-code to the value 0 ("OPTION_ALREQ") and sets 'option-len (2)' to the length of the remainder of the option. The Client includes appropriate 'Link ID, 'DSCP' and 'Prf' values for the underlying interface over which the Solicit message will be issued the same as specified for an S/TLLAO Section 3.4. The Server Templin Expires January 28, 2017 [Page 26] Internet-Draft AERO July 2016 will register each value with the Link ID in the Client's neighbor cache entry. The Client finally includes any necessary authentication options to identify itself to the DHCPv6 server, and sends the encapsulated Solicit message via the underlying interface corresponding to Link ID. (Note that this implies that the Client must send additional Rebind messages with ALREQ options to the server following the initial PD exchange using different underlying interfaces and their corresponding Link IDs if it wishes to register additional link-layer addresses and their associated DSCPs.) When the Client receives its ACP via a Reply from the AERO Server, it creates a static neighbor cache entry with the Server's link-local address as the network-layer address and the Server's encapsulation address as the link-layer address. The Client then considers the link-layer address of the Server as the primary default encapsulation address for forwarding packets for which no more-specific forwarding information is available. The Client further applies the MTU value in the ALREP option to its AERO interface, then caches any ASPs included in the ALREP option as ASPs to apply to the AERO link. Next, the Client autoconfigures an AERO address for each of the delegated ACPs, assigns the address(es) to the AERO interface and sub-delegates the ACPs to its attached EUNs and/or the Client's own internal virtual interfaces. Alternatively, the Client can configure as many addresses as it wants from /64 prefixes taken from the ACPs and assign them to either an internal virtual interface ("weak end- system") or to the AERO interface itself ("strong end-system") [RFC1122] while black-holing the remaining portions of the /64s. Finally, the Client assigns one or more default IP routes to the AERO interface with the link-local address of a Server as the next hop. After AERO address autoconfiguration, the Client SHOULD begin using the AERO address as the source address for further DHCPv6 messaging. The Client subsequently renews its ACP delegations through each of its Servers by sending Renew messages with the link-layer address of a Server as the link-layer destination address and the same options that were used in the initial PD request. Note that if the Client does not issue a Renew before the delegations expire (e.g., if the Client has been out of touch with the Server for a considerable amount of time) it must re-initiate the DHCPv6 PD procedure. Since the addresses assigned to the Client's AERO interface are obtained from the unique ACP delegations it receives, there is no need for DAD on AERO links. Other nodes maliciously attempting to hijack addresses from an authorized Client's ACPs will be denied access to the network by the Server due to an unacceptable link-layer address and/or security parameters (see: Security Considerations). Templin Expires January 28, 2017 [Page 27] Internet-Draft AERO July 2016 When a Client attempts to perform a DHCPv6 PD exchange with a Server that is too busy to service the request, the Client may receive either a "NoPrefixAvail" status code in the Server's Reply per [RFC3633] or no reply at all. In that case, the Client SHOULD discontinue DHCPv6 PD attempts through this Server and try another Server. 3.15.2.1. Autoconfiguration for Constrained Platforms On some platforms (e.g., popular cell phone operating systems), the act of assigning a default IPv6 route and/or assigning an address to an interface may not be permitted from a user application due to security policy. Typically, those platforms include a TUN/TAP interface [TUNTAP] that acts as a point-to-point conduit between user applications and the AERO interface. In that case, the Client can instead generate a "synthesized RA" message. The message conforms to [RFC4861] and is prepared as follows: o the IPv6 source address is the Client's AERO address o the IPv6 destination address is all-nodes multicast o the Router Lifetime is set to a time that is no longer than the ACP DHCPv6 lifetime o the message does not include a Source Link Layer Address Option (SLLAO) o the message includes a Prefix Information Option (PIO) with a /64 prefix taken from the ACP as the prefix for autoconfiguration The Client then sends the synthesized RA message via the TUN/TAP interface, where the operating system kernel will interpret it as though it were generated by an actual router. The operating system will then install a default route and use StateLess Address AutoConfiguration (SLAAC) to configure an IPv6 address on the TUN/TAP interface. Methods for similarly installing an IPv4 default route and IPv4 address on the TUN/TAP interface are based on synthesized DHCPv4 messages [RFC2131]. 3.15.3. AERO Server Behavior AERO Servers configure a DHCPv6 server function on their AERO links. AERO Servers arrange to add their encapsulation layer IP addresses (i.e., their link-layer addresses) to a static map of Server addresses for the link and/or the DNS resource records for the FQDN "linkupnetworks.[domainname]" before entering service. Templin Expires January 28, 2017 [Page 28] Internet-Draft AERO July 2016 When an AERO Server receives a prospective Client's Solicit on its AERO interface, and the Server is too busy to service the message, it SHOULD return a Reply with status code "NoPrefixAvail" per [RFC3633]. Otherwise, the Server authenticates the message. If authentication succeeds, the Server determines the correct ACPs to delegate to the Client by searching the Client database. When the Server delegates the ACPs, it also creates IP forwarding table entries so that the AERO routing system will propagate the ACPs to all Relays that aggregate the corresponding ASP (see: Section 3.7). Next, the Server prepares a Reply message to send to the Client while using fe80::ID as the IPv6 source address, the link- local address taken from the Client's Solicit as the IPv6 destination address, the Server's link-layer address as the source link-layer address, and the Client's link-layer address as the destination link- layer address. The server also includes IA_PD options with the delegated ACPs. Since the Client may experience a fault that prevents it from issuing a Release before departing from the network, Servers should set a short prefix lifetime (e.g., 40 seconds) so that stale prefix delegation state can be flushed out of the network. The Server also includes an ALREP option that includes configuration information pertaining to the Client's ALREQ. (Note that if the Client did not include an ALREQ option in its DHCPv6 message, the Server MUST still include an ALREP option in the corresponding reply.)The ALREP option is formatted as shown in Figure 5: Templin Expires January 28, 2017 [Page 29] Internet-Draft AERO July 2016 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | OPTION_VENDOR_OPTS | option-len (1) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | enterprise-number = 45282 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | opt-code = OPTION_ALREP (1) | option-len (2) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Link ID | Reserved | UDP Port Number | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | + + | | + IP Address + | | + + | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |Maximum Transmission Unit (MTU)| Maximum Fragment Unit (MFU) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | + AERO Service Prefix (ASP) #1 +-+-+-+-+-+-+-+-+ | | Prefix Len | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | + AERO Service Prefix (ASP) #2 +-+-+-+-+-+-+-+-+ | | Prefix Len | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ ~ ~ ~ ~ Figure 5: AERO Link-registration Reply (ALREP) Option In the ALREP, the Server sets 'option-code' to OPTION_VENDOR_OPTS, sets 'option-length (1)' to the length of the option, sets 'enterprise-number' to 45282 (see: "IANA Considerations"), sets opt- code to OPTION_ALREP (1), and sets 'option-len (2)' to the length of the remainder of the option. Next, the Server sets 'Link ID' to the same value that appeared in the ALREQ (or '0' if the Client did not include an ALREQ), sets Reserved to 0 and sets 'UDP Port Number' and 'IP address' to the link-layer address observed in the Client's DHCPv6 message. The Server next sets MTU and MFU according to the considerations specified in Section 3.13. Templin Expires January 28, 2017 [Page 30] Internet-Draft AERO July 2016 The Server finally includes one or more ASP with the IP prefix as it would appear in the interface identifier portion of the corresponding AERO address (see: Section 3.3), except that the low-order 8 bits of the ASP field encode the prefix length instead of the low-order 8 bits of the prefix. The longest prefix that can therefore appear as an ASP is /56 for IPv6 or /24 for IPv4. When the Server admits the Reply message into the AERO interface, it creates a static neighbor cache entry for the Client based on the DUID and AERO addresses with lifetime set to no more than the delegation lifetimes and the Client's link-layer address as the link- layer address for the Link ID specified in the ALREQ. The Server then uses the Client link-layer address information in the ALREQ option as the link-layer address for encapsulation based on the (DSCP, Prf) information. After the initial DHCPv6 PD exchange, the AERO Server maintains the neighbor cache entry for the Client until the delegation lifetimes expire. If the Client issues a Renew, the Server extends the lifetimes. If the Client issues a Release, or if the Client does not issue a Renew before the lifetime expires, the Server deletes the neighbor cache entry for the Client and withdraws the IP routes from the AERO routing system. 3.15.3.1. Lightweight DHCPv6 Relay Agent (LDRA) AERO Clients and Servers are always on the same link (i.e., the AERO link) from the perspective of DHCPv6. However, in some implementations the DHCPv6 server and AERO interface driver may be located in separate modules. In that case, the Server's AERO interface driver module can act as a Lightweight DHCPv6 Relay Agent (LDRA)[RFC6221] to relay DHCPv6 messages to and from the DHCPv6 server module. When the LDRA receives a DHCPv6 message from a client, it prepares an ALREP option the same as described above then wraps the option in a Relay-Supplied DHCP Option option (RSOO) [RFC6422]. The LDRA then incorporates the option into the Relay-Forward message and forwards the message to the DHCPv6 server. When the DHCPv6 server receives the Relay-Forward message, it caches the ALREP option and authenticates the encapsulated DHCPv6 message. The DHCPv6 server subsequently ignores the ALREQ option itself, since the relay has already included the ALREP option. When the DHCPv6 server prepares a Reply message, it then includes the ALREP option in the body of the message along with any other options, then wraps the message in a Relay-Reply message. The DHCPv6 server Templin Expires January 28, 2017 [Page 31] Internet-Draft AERO July 2016 then delivers the Relay-Reply message to the LDRA, which discards the Relay-Reply wrapper and delivers the DHCPv6 message to the Client. 3.15.4. Deleting Link Registrations After an AERO Client registers its Link IDs and their associated (DSCP,Prf) values with the AERO Server, the Client may wish to delete one or more Link registrations, e.g., if an underlying link becomes unavailable. To do so, the Client prepares a Rebind message that includes an AERO Link-registration Delete (ALDEL) option and sends the Rebind message to the Server over any available underlying link. The ALDEL option is formatted as shown in Figure 6: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | OPTION_VENDOR_OPTS | option-len (1) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | enterprise-number = 45282 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | opt-code = OPTION_ALDEL (2) | option-len (2) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Link ID #1 | Link ID #2 | Link ID #3 | ... +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+- Figure 6: AERO Link-registration Delete (ALDEL) Option In the ALDEL, the Client sets 'option-code' to OPTION_VENDOR_OPTS, sets 'option-length (1)' to the length of the option, sets 'enterprise-number' to 45282 (see: "IANA Considerations"), sets optcode to OPTION_ALDEL (2), and sets 'option-len (2)' to the length of the remainder of the option. Next, the Server includes each 'Link ID' value that it wishes to delete. If the Client wishes to discontinue use of a Server and thereby delete all of its Link ID associations, it must issue a Release to delete the entire neighbor cache entry, i.e., instead of issuing a Rebind with one or more ALDEL options. 3.16. AERO Forwarding Agent Behavior AERO Servers MAY associate with one or more companion AERO Forwarding Agents as platforms for offloading high-speed data plane traffic. When an AERO Server receives a Client's Solicit/Renew/Rebind/Release message, it services the message then forwards the corresponding Reply message to the Forwarding Agent. When the Forwarding Agent receives the Reply message, it creates, updates or deletes a neighbor Templin Expires January 28, 2017 [Page 32] Internet-Draft AERO July 2016 cache entry with the Client's AERO address and link-layer information included in the Reply message. The Forwarding Agent then forwards the Reply message back to the AERO Server, which forwards the message to the Client. In this way, Forwarding Agent state is managed in conjunction with Server state, with the Client responsible for reliability. When an AERO Server receives a data packet on an AERO interface with a network layer destination address for which it has distributed forwarding information to a Forwarding Agent, the Server returns a Redirect message to the source neighbor (subject to rate limiting) then forwards the data packet as usual. The Redirect message includes a TLLAO with the link-layer address of the Forwarding Engine. When the source neighbor receives the Redirect message, it SHOULD record the link-layer address in the TLLAO as the encapsulation addresses to use for sending subsequent data packets. However, the source MUST continue to use the primary link-layer address of the Server as the encapsulation address for sending control messages. 3.17. AERO Intradomain Route Optimization When a source Client forwards packets to a prospective correspondent Client within the same AERO link domain (i.e., one for which the packet's destination address is covered by an ASP), the source Client MAY initiate an intra-domain AERO route optimization procedure. It is important to note that this procedure is initiated by the Client; if the procedure were initiated by the Server, the Server would have no way of knowing whether the Client was actually able to contact the correspondent over the route-optimized path. The procedure is based on an exchange of IPv6 ND messages using a chain of AERO Servers and Relays as a trust basis. This procedure is in contrast to the Return Routability procedure required for route optimization to a correspondent Client located in the Internet as described in Section 3.22. The following sections specify the AERO intradomain route optimization procedure. 3.17.1. Reference Operational Scenario Figure 7 depicts the AERO intradomain route optimization reference operational scenario, using IPv6 addressing as the example (while not shown, a corresponding example for IPv4 addressing can be easily constructed). The figure shows an AERO Relay ('R1'), two AERO Servers ('S1', 'S2'), two AERO Clients ('C1', 'C2') and two ordinary IPv6 hosts ('H1', 'H2'): Templin Expires January 28, 2017 [Page 33] Internet-Draft AERO July 2016 +--------------+ +--------------+ +--------------+ | Server S1 | | Relay R1 | | Server S2 | +--------------+ +--------------+ +--------------+ fe80::2 fe80::1 fe80::3 L2(S1) L2(R1) L2(S2) | | | X-----+-----+------------------+-----------------+----+----X | AERO Link | L2(A) L2(B) fe80::2001:db8:0:0 fe80::2001:db8:1:0 +--------------+ +--------------+ |AERO Client C1| |AERO Client C2| +--------------+ +--------------+ 2001:DB8:0::/48 2001:DB8:1::/48 | | .-. .-. ,-( _)-. 2001:db8:0::1 2001:db8:1::1 ,-( _)-. .-(_ IP )-. +---------+ +---------+ .-(_ IP )-. (__ EUN )--| Host H1 | | Host H2 |--(__ EUN ) `-(______)-' +---------+ +---------+ `-(______)-' Figure 7: AERO Reference Operational Scenario In Figure 7, Relay ('R1') assigns the address fe80::1 to its AERO interface with link-layer address L2(R1), Server ('S1') assigns the address fe80::2 with link-layer address L2(S1),and Server ('S2') assigns the address fe80::3 with link-layer address L2(S2). Servers ('S1') and ('S2') next arrange to add their link-layer addresses to a published list of valid Servers for the AERO link. AERO Client ('C1') receives the ACP 2001:db8:0::/48 in a DHCPv6 PD exchange via AERO Server ('S1') then assigns the address fe80::2001:db8:0:0 to its AERO interface with link-layer address L2(C1). Client ('C1') configures a default route and neighbor cache entry via the AERO interface with next-hop address fe80::2 and link- layer address L2(S1), then sub-delegates the ACP to its attached EUNs. IPv6 host ('H1') connects to the EUN, and configures the address 2001:db8:0::1. AERO Client ('C2') receives the ACP 2001:db8:1::/48 in a DHCPv6 PD exchange via AERO Server ('S2') then assigns the address fe80::2001:db8:1:0 to its AERO interface with link-layer address L2(C2). Client ('C2') configures a default route and neighbor cache entry via the AERO interface with next-hop address fe80::3 and link- layer address L2(S2), then sub-delegates the ACP to its attached EUNs. IPv6 host ('H2') connects to the EUN, and configures the address 2001:db8:1::1. Templin Expires January 28, 2017 [Page 34] Internet-Draft AERO July 2016 3.17.2. Concept of Operations Again, with reference to Figure 7, when source host ('H1') sends a packet to destination host ('H2'), the packet is first forwarded over the source host's attached EUN to Client ('C1'). Client ('C1') then forwards the packet via its AERO interface to Server ('S1') and also sends a Predirect message toward Client ('C2') via Server ('S1'). Server ('S1') then re-encapsulates and forwards both the packet and the Predirect message out the same AERO interface toward Client ('C2') via Relay ('R1'). When Relay ('R1') receives the packet and Predirect message, it consults its forwarding table to discover Server ('S2') as the next hop toward Client ('C2'). Relay ('R1') then forwards both the packet and the Predirect message to Server ('S2'), which then forwards them to Client ('C2'). After Client ('C2') receives the Predirect message, it process the message and returns a Redirect message toward Client ('C1') via Server ('S2'). During the process, Client ('C2') also creates or updates a dynamic neighbor cache entry for Client ('C1'). When Server ('S2') receives the Redirect message, it re-encapsulates the message and forwards it on to Relay ('R1'), which forwards the message on to Server ('S1') which forwards the message on to Client ('C1'). After Client ('C1') receives the Redirect message, it processes the message and creates or updates a dynamic neighbor cache entry for Client ('C2'). Following the above Predirect/Redirect message exchange, forwarding of packets from Client ('C1') to Client ('C2') without involving any intermediate nodes is enabled. The mechanisms that support this exchange are specified in the following sections. 3.17.3. Message Format AERO Redirect/Predirect messages use the same format as for IPv6 ND Redirect messages depicted in Section 4.5 of [RFC4861], but also include a new "Prefix Length" field taken from the low-order 8 bits of the Redirect message Reserved field. For IPv6, valid values for the Prefix Length field are 0 through 64; for IPv4, valid values are 0 through 32. The Redirect/Predirect messages are formatted as shown in Figure 8: Templin Expires January 28, 2017 [Page 35] Internet-Draft AERO July 2016 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type (=137) | Code (=0/1) | Checksum | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Reserved | Prefix Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | + + | | + Target Address + | | + + | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | + + | | + Destination Address + | | + + | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Options ... +-+-+-+-+-+-+-+-+-+-+-+- Figure 8: AERO Redirect/Predirect Message Format 3.17.4. Sending Predirects When a Client forwards a packet with a source address from one of its ACPs toward a destination address covered by an ASP (i.e., toward another AERO Client connected to the same AERO link), the source Client MAY send a Predirect message forward toward the destination Client via the Server. In the reference operational scenario, when Client ('C1') forwards a packet toward Client ('C2'), it MAY also send a Predirect message forward toward Client ('C2'), subject to rate limiting (see Section 8.2 of [RFC4861]). Client ('C1') prepares the Predirect message as follows: o the link-layer source address is set to 'L2(C1)' (i.e., the link- layer address of Client ('C1')). o the link-layer destination address is set to 'L2(S1)' (i.e., the link-layer address of Server ('S1')). Templin Expires January 28, 2017 [Page 36] Internet-Draft AERO July 2016 o the network-layer source address is set to fe80::2001:db8:0:0 (i.e., the AERO address of Client ('C1')). o the network-layer destination address is set to fe80::2001:db8:1:0 (i.e., the AERO address of Client ('C2')). o the Type is set to 137. o the Code is set to 1 to indicate "Predirect". o the Prefix Length is set to the length of the prefix to be assigned to the Target Address. o the Target Address is set to fe80::2001:db8:0:0 (i.e., the AERO address of Client ('C1')). o the Destination Address is set to the source address of the originating packet that triggered the Predirection event. (If the originating packet is an IPv4 packet, the address is constructed in IPv4-compatible IPv6 address format). o the message includes one or more TLLAOs with Link ID and DSCPs set to appropriate values for Client ('C1')'s underlying interfaces, and with UDP Port Number and IP Address set to 0'. o the message SHOULD include a Timestamp option and a Nonce option. o the message includes a Redirected Header Option (RHO) that contains the originating packet truncated if necessary to ensure that at least the network-layer header is included but the size of the message does not exceed 1280 bytes. Note that the act of sending Predirect messages is cited as "MAY", since Client ('C1') may have advanced knowledge that the direct path to Client ('C2') would be unusable or otherwise undesirable. If the direct path later becomes unusable after the initial route optimization, Client ('C1') simply allows packets to again flow through Server ('S1'). 3.17.5. Re-encapsulating and Relaying Predirects When Server ('S1') receives a Predirect message from Client ('C1'), it first verifies that the TLLAOs in the Predirect are a proper subset of the Link IDs in Client ('C1')'s neighbor cache entry. If the Client's TLLAOs are not acceptable, Server ('S1') discards the message. Otherwise, Server ('S1') validates the message according to the Redirect message validation rules in Section 8.1 of [RFC4861], except that the Predirect has Code=1. Server ('S1') also verifies Templin Expires January 28, 2017 [Page 37] Internet-Draft AERO July 2016 that Client ('C1') is authorized to use the Prefix Length in the Predirect when applied to the AERO address in the network-layer source address by searching for the AERO address in the neighbor cache. If validation fails, Server ('S1') discards the Predirect; otherwise, it copies the correct UDP Port numbers and IP Addresses for Client ('C1')'s links into the (previously empty) TLLAOs. Server ('S1') then examines the network-layer destination address of the Predirect to determine the next hop toward Client ('C2') by searching for the AERO address in the neighbor cache. Since Client ('C2') is not one of its neighbors, Server ('S1') re-encapsulates the Predirect and relays it via Relay ('R1') by changing the link-layer source address of the message to 'L2(S1)' and changing the link-layer destination address to 'L2(R1)'. Server ('S1') finally forwards the re-encapsulated message to Relay ('R1') without decrementing the network-layer TTL/Hop Limit field. When Relay ('R1') receives the Predirect message from Server ('S1') it determines that Server ('S2') is the next hop toward Client ('C2') by consulting its forwarding table. Relay ('R1') then re- encapsulates the Predirect while changing the link-layer source address to 'L2(R1)' and changing the link-layer destination address to 'L2(S2)'. Relay ('R1') then relays the Predirect via Server ('S2'). When Server ('S2') receives the Predirect message from Relay ('R1') it determines that Client ('C2') is a neighbor by consulting its neighbor cache. Server ('S2') then re-encapsulates the Predirect while changing the link-layer source address to 'L2(S2)' and changing the link-layer destination address to 'L2(C2)'. Server ('S2') then forwards the message to Client ('C2'). 3.17.6. Processing Predirects and Sending Redirects When Client ('C2') receives the Predirect message, it accepts the Predirect only if the message has a link-layer source address of one of its Servers (e.g., L2(S2)). Client ('C2') further accepts the message only if it is willing to serve as a redirection target. Next, Client ('C2') validates the message according to the Redirect message validation rules in Section 8.1 of [RFC4861], except that it accepts the message even though Code=1 and even though the network- layer source address is not that of it's current first-hop router. In the reference operational scenario, when Client ('C2') receives a valid Predirect message, it either creates or updates a dynamic neighbor cache entry that stores the Target Address of the message as the network-layer address of Client ('C1') , stores the link-layer addresses found in the TLLAOs as the link-layer addresses of Client Templin Expires January 28, 2017 [Page 38] Internet-Draft AERO July 2016 ('C1') and stores the Prefix Length as the length to be applied to the network-layer address for forwarding purposes. Client ('C2') then sets AcceptTime for the neighbor cache entry to ACCEPT_TIME. After processing the message, Client ('C2') prepares a Redirect message response as follows: o the link-layer source address is set to 'L2(C2)' (i.e., the link- layer address of Client ('C2')). o the link-layer destination address is set to 'L2(S2)' (i.e., the link-layer address of Server ('S2')). o the network-layer source address is set to fe80::2001:db8:1:0 (i.e., the AERO address of Client ('C2')). o the network-layer destination address is set to fe80::2001:db8:0:0 (i.e., the AERO address of Client ('C1')). o the Type is set to 137. o the Code is set to 0 to indicate "Redirect". o the Prefix Length is set to the length of the prefix to be applied to the Target Address. o the Target Address is set to fe80::2001:db8:1:0 (i.e., the AERO address of Client ('C2')). o the Destination Address is set to the destination address of the originating packet that triggered the Redirection event. (If the originating packet is an IPv4 packet, the address is constructed in IPv4-compatible IPv6 address format). o the message includes one or more TLLAOs with Link ID and DSCPs set to appropriate values for Client ('C2')'s underlying interfaces, and with UDP Port Number and IP Address set to '0'. o the message SHOULD include a Timestamp option and MUST echo the Nonce option received in the Predirect (i.e., if a Nonce option is included). o the message includes as much of the RHO copied from the corresponding Predirect message as possible such that at least the network-layer header is included but the size of the message does not exceed 1280 bytes. Templin Expires January 28, 2017 [Page 39] Internet-Draft AERO July 2016 After Client ('C2') prepares the Redirect message, it sends the message to Server ('S2'). 3.17.7. Re-encapsulating and Relaying Redirects When Server ('S2') receives a Redirect message from Client ('C2'), it first verifies that the TLLAOs in the Redirect are a proper subset of the Link IDs in Client ('C2')'s neighbor cache entry. If the Client's TLLAOs are not acceptable, Server ('S2') discards the message. Otherwise, Server ('S2') validates the message according to the Redirect message validation rules in Section 8.1 of [RFC4861]. Server ('S2') also verifies that Client ('C2') is authorized to use the Prefix Length in the Redirect when applied to the AERO address in the network-layer source address by searching for the AERO address in the neighbor cache. If validation fails, Server ('S2') discards the Redirect; otherwise, it copies the correct UDP Port numbers and IP Addresses for Client ('C2')'s links into the (previously empty) TLLAOs. Server ('S2') then examines the network-layer destination address of the Redirect to determine the next hop toward Client ('C1') by searching for the AERO address in the neighbor cache. Since Client ('C1') is not a neighbor, Server ('S2') re-encapsulates the Redirect and relays it via Relay ('R1') by changing the link-layer source address of the message to 'L2(S2)' and changing the link-layer destination address to 'L2(R1)'. Server ('S2') finally forwards the re-encapsulated message to Relay ('R1') without decrementing the network-layer TTL/Hop Limit field. When Relay ('R1') receives the Redirect message from Server ('S2') it determines that Server ('S1') is the next hop toward Client ('C1') by consulting its forwarding table. Relay ('R1') then re-encapsulates the Redirect while changing the link-layer source address to 'L2(R1)' and changing the link-layer destination address to 'L2(S1)'. Relay ('R1') then relays the Redirect via Server ('S1'). When Server ('S1') receives the Redirect message from Relay ('R1') it determines that Client ('C1') is a neighbor by consulting its neighbor cache. Server ('S1') then re-encapsulates the Redirect while changing the link-layer source address to 'L2(S1)' and changing the link-layer destination address to 'L2(C1)'. Server ('S1') then forwards the message to Client ('C1'). 3.17.8. Processing Redirects When Client ('C1') receives the Redirect message, it accepts the message only if it has a link-layer source address of one of its Servers (e.g., ''L2(S1)'). Next, Client ('C1') validates the message Templin Expires January 28, 2017 [Page 40] Internet-Draft AERO July 2016 according to the Redirect message validation rules in Section 8.1 of [RFC4861], except that it accepts the message even though the network-layer source address is not that of it's current first-hop router. Following validation, Client ('C1') then processes the message as follows. In the reference operational scenario, when Client ('C1') receives the Redirect message, it either creates or updates a dynamic neighbor cache entry that stores the Target Address of the message as the network-layer address of Client ('C2'), stores the link-layer addresses found in the TLLAOs as the link-layer addresses of Client ('C2') and stores the Prefix Length as the length to be applied to the network-layer address for forwarding purposes. Client ('C1') then sets ForwardTime for the neighbor cache entry to FORWARD_TIME. Now, Client ('C1') has a neighbor cache entry with a valid ForwardTime value, while Client ('C2') has a neighbor cache entry with a valid AcceptTime value. Thereafter, Client ('C1') may forward ordinary network-layer data packets directly to Client ('C2') without involving any intermediate nodes, and Client ('C2') can verify that the packets came from an acceptable source. (In order for Client ('C2') to forward packets to Client ('C1'), a corresponding Predirect/Redirect message exchange is required in the reverse direction; hence, the mechanism is asymmetric.) 3.17.9. Server-Oriented Redirection In some environments, the Server nearest the target Client may need to serve as the redirection target, e.g., if direct Client-to-Client communications are not possible. In that case, the Server prepares the Redirect message the same as if it were the destination Client (see: Section 3.17.6), except that it writes its own link-layer address in the TLLAO option. The Server must then maintain a dynamic neighbor cache entry for the redirected source Client. 3.17.10. Route Optimization Policy Although the Client is responsible for initiating route optimization through the transmission of Predirect messages, the Server is the policy enforcement point that determines whether route optimization is permitted. For example, on some AERO links route optimization would allow traffic to circumvent critical network-based traffic interception points. In those cases, the Server can deny route optimization requests by simply discarding any Predirect messages instead of forwarding them. Templin Expires January 28, 2017 [Page 41] Internet-Draft AERO July 2016 3.17.11. Route Optimization and Multiple ACPs Clients that receive multiple non-contiguous ACP delegations must perform route optimization for each of the individual ACPs based on demand of traffic with source addresses taken from those prefixes. For example, if Client C1 has already performed route optimization for destination ACP X on behalf of its source ACP Y, it must also perform route optimization for X on behalf of its source ACP Z. As a result, source route optimization state cannot be shared between non- contiguous ACPs and must be managed separately. 3.18. Neighbor Unreachability Detection (NUD) AERO nodes perform Neighbor Unreachability Detection (NUD) by sending unicast NS messages to elicit solicited NA messages from neighbors the same as described in [RFC4861]. NUD is performed either reactively in response to persistent L2 errors (see Section 3.14) or proactively to test existing neighbor cache entries. When an AERO node sends an NS/NA message, it MUST use its link-local address as the IPv6 source address and the link-local address of the neighbor as the IPv6 destination address. When an AERO node receives an NS message or a solicited NA message, it accepts the message if it has a neighbor cache entry for the neighbor; otherwise, it ignores the message. When a source Client is redirected to a target Client it SHOULD proactively test the direct path by sending an initial NS message to elicit a solicited NA response. While testing the path, the source Client can optionally continue sending packets via the Server, maintain a small queue of packets until target reachability is confirmed, or (optimistically) allow packets to flow directly to the target. The source Client SHOULD thereafter continue to test the direct path to the target Client (see Section 7.3 of [RFC4861]) periodically in order to keep dynamic neighbor cache entries alive. In particular, while the source Client is actively sending packets to the target Client it SHOULD also send NS messages separated by RETRANS_TIMER milliseconds in order to receive solicited NA messages. If the source Client is unable to elicit a solicited NA response from the target Client after MAX_RETRY attempts, it SHOULD set ForwardTime to 0 and resume sending packets via one of its Servers. Otherwise, the source Client considers the path usable and SHOULD thereafter process any link-layer errors as a hint that the direct path to the target Client has either failed or has become intermittent. When ForwardTime for a dynamic neighbor cache entry expires, the source Client resumes sending any subsequent packets via a Server and Templin Expires January 28, 2017 [Page 42] Internet-Draft AERO July 2016 may (eventually) attempt to re-initiate the AERO redirection process. When AcceptTime for a dynamic neighbor cache entry expires, the target Client discards any subsequent packets received directly from the source Client. When both ForwardTime and AcceptTime for a dynamic neighbor cache entry expire, the Client deletes the neighbor cache entry. 3.19. Mobility Management 3.19.1. Announcing Link-Layer Address Changes When a Client needs to change its link-layer address, e.g., due to a mobility event, it issues an immediate Rebind to each of its Servers using the new link-layer address as the source address and with an ALREQ that includes the correct Link ID and DSCP values. If authentication succeeds, the Server then updates its neighbor cache and sends a Reply. Note that if the Client does not issue a Rebind before the prefix delegation lifetime expires (e.g., if the Client has been out of touch with the Server for a considerable amount of time), the Server's Reply will report NoBinding and the Client must re-initiate the DHCPv6 PD procedure. Next, the Client sends Predirect messages to each of its correspondent Client neighbors using the same procedures as specified in Section 3.17.4. The Client sends the Predirect messages via a Server the same as if it was performing the initial route optimization procedure with the correspondent. The Predirect message will update the correspondent' link layer address mapping for the Client. 3.19.2. Bringing New Links Into Service When a Client needs to bring a new underlying interface into service (e.g., when it activates a new data link), it issues an immediate Rebind to each of its Servers using the new link-layer address as the source address and with an ALREQ that includes the new Link ID and DSCP values. If authentication succeeds, the Server then updates its neighbor cache and sends a Reply. The Client MAY then send Predirect messages to each of its correspondent Clients to inform them of the new link-layer address as described in Section 3.19.1. 3.19.3. Removing Existing Links from Service When a Client needs to remove an existing underlying interface from service (e.g., when it de-activates an existing data link), it issues an immediate Rebind to each of its Servers over any available link with an ALDEL that includes the deprecated Link ID. If authentication succeeds, the Server then updates its neighbor cache Templin Expires January 28, 2017 [Page 43] Internet-Draft AERO July 2016 and sends a Reply. The Client SHOULD then send Predirect messages to each of its correspondent Clients to inform them of the deprecated link-layer address as described in Section 3.19.1. 3.19.4. Moving to a New Server When a Client associates with a new Server, it performs the Client procedures specified in Section 3.15.2. When a Client disassociates with an existing Server, it sends a Release message via a new Server to the unicast link-local network layer address of the old Server. The new Server then writes its own link-layer address in the Release message IP source address and forwards the message to the old Server. When the old Server receives the Release, it first authenticates the message. Next, it resets the Client's neighbor cache entry lifetime to 3 seconds, rewrites the link-layer address in the neighbor cache entry to the address of the new Server, then returns a Reply message to the Client via the old Server. When the lifetime expires, the old Server withdraws the IP route from the AERO routing system and deletes the neighbor cache entry for the Client. The Client can then use the Reply message to verify that the termination signal has been processed, and can delete both the default route and the neighbor cache entry for the old Server. (Note that since Release/Reply messages may be lost in the network the Client MUST retry until it gets a Reply indicating that the Release was successful. If the Client does not receive a Reply after MAX_RETRY attempts, the old Server may have failed and the Client should discontinue its Release attempts.) Clients SHOULD NOT move rapidly between Servers in order to avoid causing excessive oscillations in the AERO routing system. Such oscillations could result in intermittent reachability for the Client itself, while causing little harm to the network. Examples of when a Client might wish to change to a different Server include a Server that has gone unreachable, topological movements of significant distance, etc. 3.19.5. Packet Queueing for Mobility AERO Clients and Servers should maintain a samll queue of packets they have recently sent to an AERO neighbor, e.g., a 1 second window. If the AERO neighbor moves, the AERO node MAY retransmit the queued packets to ensure that they are delviered to the AERO neighbor's new location. Templin Expires January 28, 2017 [Page 44] Internet-Draft AERO July 2016 Note that this may have performance implications for asymmetric paths. For example, if the AERO neighbor moves from a 50mbps link to a 128kbps link, retransmitting a 1 second window could lead to significant congestion. 3.20. Proxy AERO Proxy Mobile IPv6 (PMIPv6) [RFC5213][RFC5844][RFC5949] presents a network-based localized mobility management scheme for use within an access network domain. It is typically used in WiFi and cellular wireless access networks, and allows Mobile Nodes (MNs) to receive and retain an IP address that remains stable within the access network domain without needing to implement any special mobility protocols. In the PMIPv6 architecture, access network devices known as Mobility Access Gateways (MAGs) provide MNs with an access link abstraction and receive prefixes for the MNs from a Local Mobility Anchor (LMA). In a proxy AERO domain, a proxy AERO Client (acting as a MAG) can similarly provide proxy services for MNs that do not participate in AERO messaging. The proxy Client presents an access link abstraction to MNs, and performs DHCPv6 PD exchanges over the AERO interface with an AERO Server (acting as an LMA) to receive ACPs for address provisioning of new MNs that come onto an access link. This scheme assumes that proxy Clients act as fixed (non-mobile) infrastructure elements under the same administrative trust basis as for Relays and Servers. When an MN comes onto an access link within a proxy AERO domain for the first time, the proxy Client authenticates the MN and obtains a unique identifier that it can use as a DHCPv6 DUID then sends a Solicit message to its Server. When the Server delegates an ACP and returns a Reply, the proxy Client creates an AERO address for the MN and assigns the ACP to the MN's access link. The proxy Client then configures itself as a default router for the MN and provides address autoconfiguration services (e.g., SLAAC, DHCPv6, DHCPv4, etc.) for provisioning MN addresses from the ACP over the access link. Since the proxy Client may serve many such MNs simultaneously, it may receive multiple ACP prefix delegations and configure multiple AERO addresses, i.e., one for each MN. When two MNs are associated with the same proxy Client, the Client can forward traffic between the MNs without involving a Server since it configures the AERO addresses of both MNs and therefore also has the necessary routing information. When two MNs are associated with different proxy Clients, the source MN's Client can initiate standard AERO intradomain route optimization to discover a direct path to the Templin Expires January 28, 2017 [Page 45] Internet-Draft AERO July 2016 target MN's Client through the exchange of Predirect/Redirect messages. When an MN in a proxy AERO domain leaves an access link provided by an old proxy Client, the MN issues an access link-specific "leave" message that informs the old Client of the link-layer address of a new Client on the planned new access link. This is known as a "predictive handover". When an MN comes onto an access link provided by a new proxy Client, the MN issues an access link-specific "join" message that informs the new Client of the link-layer address of the old Client on the actual old access link. This is known as a "reactive handover". Upon receiving a predictive handover indication, the old proxy Client sends a Solicit message directly to the new Client and queues any arriving data packets addressed to the departed MN. The Solicit message includes the MN's ID as the DUID, the ACP in an IA_PD option, the old Client's address as the link-layer source address and the new Client's address as the link-layer destination address. When the new Client receives the Solicit message, it changes the link-layer source address to its own address, changes the link-layer destination address to the address of its Server, and forwards the message to the Server. At the same time, the new Client creates access link state for the ACP in anticipation of the MN's arrival (while queuing any data packets until the MN arrives), creates a neighbor cache entry for the old Client with AcceptTime set to ACCEPT_TIME, then sends a Redirect message back to the old Client. When the old Client receives the Redirect message, it creates a neighbor cache entry for the new Client with ForwardTime set to FORWARD_TIME, then forwards any queued data packets to the new Client. At the same time, the old Client sends a Release message to its Server. Finally, the old Client sends unsolicited Redirect messages to any of the ACP's correspondents with a TLLAO containing the link-layer address of the new Client. Upon receiving a reactive handover indication, the new proxy Client creates access link state for the MN's ACP, sends a Solicit message to its Server, and sends a Release message directly to the old Client. The Release message includes the MN's ID as the DUID, the ACP in an IA_PD option, the new Client's address as the link-layer source address and the old Client's address as the link-layer destination address. When the old Client receives the Release message, it changes the link-layer source address to its own address, changes the link-layer destination address to the address of its Server, and forwards the message to the Server. At the same time, the old Client sends a Predirect message back to the new Client and queues any arriving data packets addressed to the departed MN. When the new Client receives the Predirect, it creates a neighbor cache Templin Expires January 28, 2017 [Page 46] Internet-Draft AERO July 2016 entry for the old Client with AcceptTime set to ACCEPT_TIME, then sends a Redirect message back to the old Client. When the old Client receives the Redirect message, it creates a neighbor cache entry for the new Client with ForwardTime set to FORWARD_TIME, then forwards any queued data packets to the new Client. Finally, the old Client sends unsolicited Redirect messages to correspondents the same as for the predictive case. When a Server processes a Solicit message, it creates a neighbor cache entry for this ACP if none currently exists. If a neighbor cache entry already exists, however, the Server changes the link- layer address to the address of the new proxy Client (this satisfies the case of both the old Client and new Client using the same Server). When a Server processes a Release message, it resets the neighbor cache entry lifetime for this ACP to 3 seconds if the cached link- layer address matches the old proxy Client's address. Otherwise, the Server ignores the Release message (this satisfies the case of both the old Client and new Client using the same Server). When a correspondent Client receives an unsolicited Redirect message, it changes the link-layer address for the ACP's neighbor cache entry to the address of the new proxy Client. From an architectural perspective, in addition to the use of DHCPv6 PD and IPv6 ND signaling the AERO approach differs from PMIPv6 in its use of the NBMA virtual link model instead of point-to-point tunnels. This provides a more agile interface for Client/Server and Client/ Client coordinations, and also facilitates simple route optimization. The AERO routing system is also arranged in such a fashion that Clients get the same service from any Server they happen to associate with. This provides a natural fault tolerance and load balancing capability such as desired for distributed mobility management. 3.21. Extending AERO Links Through Security Gateways When an enterprise mobile device moves from a campus LAN connection to a public Internet link, it must re-enter the enterprise via a security gateway that has both a physical interface connection to the Internet and a physical interface connection to the enterprise internetwork. This most often entails the establishment of a Virtual Private Network (VPN) link over the public Internet from the mobile device to the security gateway. During this process, the mobile device supplies the security gateway with its public Internet address as the link-layer address for the VPN. The mobile device then acts as an AERO Client to negotiate with the security gateway to obtain its ACP. Templin Expires January 28, 2017 [Page 47] Internet-Draft AERO July 2016 In order to satisfy this need, the security gateway also operates as an AERO Server with support for AERO Client proxying. In particular, when a mobile device (i.e., the Client) connects via the security gateway (i.e., the Server), the Server provides the Client with an ACP in a DHCPv6 PD exchange the same as if it were attached to an enterprise campus access link. The Server then replaces the Client's link-layer source address with the Server's enterprise-facing link- layer address in all AERO messages the Client sends toward neighbors on the AERO link. The AERO messages are then delivered to other devices on the AERO link as if they were originated by the security gateway instead of by the AERO Client. In the reverse direction, the AERO messages sourced by devices within the enterprise network can be forwarded to the security gateway, which then replaces the link-layer destination address with the Client's link-layer address and replaces the link-layer source address with its own (Internet-facing) link- layer address. After receiving the ACP, the Client can send IP packets that use an address taken from the ACP as the network layer source address, the Client's link-layer address as the link-layer source address, and the Server's Internet-facing link-layer address as the link-layer destination address. The Server will then rewrite the link-layer source address with the Server's own enterprise-facing link-layer address and rewrite the link-layer destination address with the target AERO node's link-layer address, and the packets will enter the enterprise network as though they were sourced from a device located within the enterprise. In the reverse direction, when a packet sourced by a node within the enterprise network uses a destination address from the Client's ACP, the packet will be delivered to the security gateway which then rewrites the link-layer destination address to the Client's link-layer address and rewrites the link- layer source address to the Server's Internet-facing link-layer address. The Server then delivers the packet across the VPN to the AERO Client. In this way, the AERO virtual link is essentially extended *through* the security gateway to the point at which the VPN link and AERO link are effectively grafted together by the link-layer address rewriting performed by the security gateway. All AERO messaging services (including route optimization and mobility signaling) are therefore extended to the Client. In order to support this virtual link grafting, the security gateway (acting as an AERO Server) must keep static neighbor cache entries for all of its associated Clients located on the public Internet. The neighbor cache entry is keyed by the AERO Client's AERO address the same as if the Client were located within the enterprise internetwork. The neighbor cache is then managed in all ways as though the Client were an ordinary AERO Client. This includes the Templin Expires January 28, 2017 [Page 48] Internet-Draft AERO July 2016 AERO IPv6 ND messaging signaling for Route Optimization and Neighbor Unreachability Detection. Note that the main difference between a security gateway acting as an AERO Server and an enterprise-internal AERO Server is that the security gateway has at least one enterprise-internal physical interface and at least one public Internet physical interface. Conversely, the enterprise-internal AERO Server has only enterprise- internal physical interfaces. For this reason security gateway proxying is needed to ensure that the public Internet link-layer addressing space is kept separate from the enterprise-internal link- layer addressing space. This is afforded through a natural extension of the security association caching already performed for each VPN client by the security gateway. 3.22. Extending IPv6 AERO Links to the Internet When an IPv6 host ('H1') with an address from an ACP owned by AERO Client ('C1') sends packets to a correspondent IPv6 host ('H2'), the packets eventually arrive at the IPv6 router that owns ('H2')s prefix. This IPv6 router may or may not be an AERO Client ('C2') either within the same home network as ('C1') or in a different home network. If Client ('C1') is currently located outside the boundaries of its home network, it will connect back into the home network via a security gateway acting as an AERO Server. The packets sent by ('H1') via ('C1') will then be forwarded through the security gateway then through the home network and finally to ('C2') where they will be delivered to ('H2'). This could lead to sub-optimal performance when ('C2') could instead be reached via a more direct route without involving the security gateway. Consider the case when host ('H1') has the IPv6 address 2001:db8:1::1, and Client ('C1') has the ACP 2001:db8:1::/64 with underlying IPv6 Internet address of 2001:db8:1000::1. Also, host ('H2') has the IPv6 address 2001:db8:2::1, and Client ('C2') has the ACP 2001:db8:2::/64 with underlying IPv6 address of 2001:db8:2000::1. Client ('C1') can determine whether 'C2' is indeed also an AERO Client willing to serve as a route optimization correspondent by resolving the AAAA records for the DNS FQDN that matches ('H2')s prefix, i.e.: '0.0.0.0.2.0.0.0.8.b.d.0.1.0.0.2.aero.linkupnetworks.net' If ('C2') is indeed a candidate correspondent, the FQDN lookup will return a PTR resource record that contains the domain name for the AERO link that manages ('C2')s ASP. Client ('C1') can then attempt Templin Expires January 28, 2017 [Page 49] Internet-Draft AERO July 2016 route optimization using an approach similar to the Return Routability procedure specified for Mobile IPv6 (MIPv6) [RFC6275]. In order to support this process, both Clients MUST intercept and decapsulate packets that have a subnet router anycast address corresponding to any of the /64 prefixes covered by their respective ACPs. To initiate the process, Client ('C1') creates a specially-crafted encapsulated Predirect message that will be routed through its home network then through ('C2')s home network and finally to ('C2') itself. Client ('C1') prepares the initial message in the exchange as follows: o The encapsulating IPv6 header source address is set to 2001:db8:1:: (i.e., the IPv6 subnet router anycast address for ('C1')s ACP) o The encapsulating IPv6 header destination address is set to 2001:db8:2:: (i.e., the IPv6 subnet router anycast address for ('C2')s ACP) o The encapsulating IPv6 header is followed by any additional encapsulation headers o The encapsulated IPv6 header source address is set to fe80::2001:db8:1:0 (i.e., the AERO address for ('C1')) o The encapsulated IPv6 header destination address is set to fe80::2001:db8:2:0 (i.e., the AERO address for ('C2')) o The encapsulated Predirect message includes all of the securing information that would occur in a MIPv6 "Home Test Init" message (format TBD) Client ('C1') then further encapsulates the message in the encapsulating headers necessary to convey the packet to the security gateway (e.g., through IPsec encapsulation) so that the message now appears "double-encapsulated". ('C1') then sends the message to the security gateway, which re-encapsulates and forwards it over the home network from where it will eventually reach ('C2'). At the same time, ('C1') creates and sends a second encapsulated Predirect message that will be routed through the IPv6 Internet without involving the security gateway. Client ('C1') prepares the message as follows: o The encapsulating IPv6 header source address is set to 2001:db8:1000:1 (i.e., the Internet IPv6 address of ('C1')) Templin Expires January 28, 2017 [Page 50] Internet-Draft AERO July 2016 o The encapsulating IPv6 header destination address is set to 2001:db8:2:: (i.e., the IPv6 subnet router anycast address for ('C2')s ACP) o The encapsulating IPv6 header is followed by any additional encapsulation headers o The encapsulated IPv6 header source address is set to fe80::2001:db8:1:0 (i.e., the AERO address for ('C1')) o The encapsulated IPv6 header destination address is set to fe80::2001:db8:2:0 (i.e., the AERO address for ('C2')) o The encapsulated Predirect message includes all of the securing information that would occur in a MIPv6 "Care-of Test Init" message (format TBD) ('C2') will receive both Predirect messages through its home network then return a corresponding Redirect for each of the Predirect messages with the source and destination addresses in the inner and outer headers reversed. The first message includes all of the securing information that would occur in a MIPv6 "Home Test" message, while the second message includes all of the securing information that would occur in a MIPv6 "Care-of Test" message (formats TBD). When ('C1') receives the Redirect messages, it performs the necessary security procedures per the MIPv6 specification. It then prepares an encapsulated NS message that includes the same source and destination addresses as for the "Care-of Test Init" Predirect message, and includes all of the securing information that would occur in a MIPv6 "Binding Update" message (format TBD) and sends the message to ('C2'). When ('C2') receives the NS message, if the securing information is correct it creates or updates a neighbor cache entry for ('C1') with fe80::2001:db8:1:0 as the network-layer address, 2001:db8:1000::1 as the link-layer address and with AcceptTime set to ACCEPT_TIME. ('C2') then sends an encapsulated NA message back to ('C1') that includes the same source and destination addresses as for the "Care- of Test" Redirect message, and includes all of the securing information that would occur in a MIPv6 "Binding Acknowledgement" message (format TBD) and sends the message to ('C1'). When ('C1') receives the NA message, it creates or updates a neighbor cache entry for ('C2') with fe80::2001:db8:2:0 as the network-layer address and 2001:db8:2:: as the link-layer address and with ForwardTime set to FORWARD_TIME, thus completing the route optimization in the forward direction. Templin Expires January 28, 2017 [Page 51] Internet-Draft AERO July 2016 ('C1') subsequently forwards encapsulated packets with outer source address 2001:db8:1000::1, with outer destination address 2001:db8:2::, with inner source address taken from the 2001:db8:1::, and with inner destination address taken from 2001:db8:2:: due to the fact that it has a securely-established neighbor cache entry with non-zero ForwardTime. ('C2') subsequently accepts any such encapsulated packets due to the fact that it has a securely- established neighbor cache entry with non-zero AcceptTime. In order to keep neighbor cache entries alive, ('C1') periodically sends additional NS messages to ('C2') and receives any NA responses. If ('C1') moves to a different point of attachment after the initial route optimization, it sends a new secured NS message to ('C2') as above to update ('C2')s neighbor cache. If ('C2') has packets to send to ('C1'), it performs a corresponding route optimization in the opposite direction following the same procedures described above. In the process, the already-established unidirectional neighbor cache entries within ('C1') and ('C2') are updated to include the now-bidirectional information. In particular, the AcceptTime and ForwardTime variables for both neighbor cache entries are updated to non-zero values, and the link-layer address for ('C1')s neighbor cache entry for ('C2') is reset to 2001:db8:2000::1. Note that two AERO Clients can use full security protocol messaging instead of Return Routability, e.g., if strong authentication and/or confidentiality are desired. In that case, security protocol key exchanges such as specified for MOBIKE [RFC4555] would be used to establish security associations and neighbor cache entries between the AERO clients. Thereafter, NS/NA messaging can be used to maintain neighbor cache entries, test reachability, and to announce mobility events. If reachability testing fails, e.g., if both Clients move at roughly the same time, the Clients can tear down the security association and neighbor cache entries and again allow packets to flow through their home network. 3.23. Encapsulation Protocol Version Considerations A source Client may connect only to an IPvX underlying network, while the target Client connects only to an IPvY underlying network. In that case, the target and source Clients have no means for reaching each other directly (since they connect to underlying networks of different IP protocol versions) and so must ignore any redirection messages and continue to send packets via their Servers. Templin Expires January 28, 2017 [Page 52] Internet-Draft AERO July 2016 3.24. Multicast Considerations When the underlying network does not support multicast, AERO Clients map link-scoped multicast addresses to the link-layer address of a Server, which acts as a multicast forwarding agent. The AERO Client also serves as an IGMP/MLD Proxy for its EUNs and/or hosted applications per [RFC4605] while using the link-layer address of the Server as the link-layer address for all multicast packets. When the underlying network supports multicast, AERO nodes use the multicast address mapping specification found in [RFC2529] for IPv4 underlying networks and use a TBD site-scoped multicast mapping for IPv6 underlying networks. In that case, border routers must ensure that the encapsulated site-scoped multicast packets do not leak outside of the site spanned by the AERO link. 3.25. Operation on AERO Links Without DHCPv6 Services When Servers on the AERO link do not provide DHCPv6 services, operation can still be accommodated through administrative configuration of ACPs on AERO Clients. In that case, administrative configurations of AERO interface neighbor cache entries on both the Server and Client are also necessary. However, this may interfere with the ability for Clients to dynamically change to new Servers, and can expose the AERO link to misconfigurations unless the administrative configurations are carefully coordinated. 3.26. Operation on Server-less AERO Links In some AERO link scenarios, there may be no Servers on the link and/ or no need for Clients to use a Server as an intermediary trust anchor. In that case, each Client acts as a Server unto itself to establish neighbor cache entries by performing direct Client-to- Client IPv6 ND message exchanges, and some other form of trust basis must be applied so that each Client can verify that the prospective neighbor is authorized to use its claimed ACP. When there is no Server on the link, Clients must arrange to receive ACPs and publish them via a secure alternate prefix delegation authority through some means outside the scope of this document. 3.27. Manually-Configured AERO Tunnels In addition to the dynamic neighbor discovery procedures for AERO link neighbors described above, AERO encapsulation can be applied to manually-configured tunnels. In that case, the tunnel endpoints use an administratively-assigned link-local address and exchange NS/NA messages the same as for dynamically-established tunnels. Templin Expires January 28, 2017 [Page 53] Internet-Draft AERO July 2016 3.28. Intradomain Routing After a tunnel neighbor relationship has been established, neighbors can use a traditional dynamic routing protocol over the tunnel to exchange routing information without having to inject the routes into the AERO routing system. 4. Implementation Status User-level and kernel-level AERO implementations have been developed and are undergoing internal testing within Boeing. An initial public release of the AERO source code was announced on the intarea mailing list on August 21, 2015, and a pointer to the code is available in the list archives. 5. IANA Considerations The IANA has assigned a 4-octet Private Enterprise Number "45282" for AERO in the "enterprise-numbers" registry. The IANA has assigned the UDP port number "8060" for an earlier experimental version of AERO [RFC6706]. This document obsoletes [RFC6706] and claims the UDP port number "8060" for all future use. No further IANA actions are required. 6. Security Considerations AERO link security considerations are the same as for standard IPv6 Neighbor Discovery [RFC4861] except that AERO improves on some aspects. In particular, AERO uses a trust basis between Clients and Servers, where the Clients only engage in the AERO mechanism when it is facilitated by a trust anchor. Unless there is some other means of authenticating the Client's identity (e.g., link-layer security), AERO nodes SHOULD also use DHCPv6 securing services (e.g., DHCPv6 authentication, Secure DHCPv6 [I-D.ietf-dhc-sedhcpv6], etc.) for Client authentication and network admission control. In particular, Clients SHOULD include authenticating information on each Solicit/Rebind/Release message they send, but omit authenticating information on Renew messages. Renew messages are exempt due to the fact that the Renew must already be checked for having a correct link-layer address and does not update any link-layer addresses. Therefore, asking the Server to also authenticate the Renew message would be unnecessary and could result in excessive processing overhead. Templin Expires January 28, 2017 [Page 54] Internet-Draft AERO July 2016 Redirect, Predirect and unsolicited NA messages SHOULD include a Timestamp option (see Section 5.3 of [RFC3971]) that other AERO nodes can use to verify the message time of origin. Predirect, NS and RS messages SHOULD include a Nonce option (see Section 5.3 of [RFC3971]) that recipients echo back in corresponding responses. AERO links must be protected against link-layer address spoofing attacks in which an attacker on the link pretends to be a trusted neighbor. Links that provide link-layer securing mechanisms (e.g., IEEE 802.1X WLANs) and links that provide physical security (e.g., enterprise network wired LANs) provide a first line of defense that is often sufficient. In other instances, additional securing mechanisms such as Secure Neighbor Discovery (SeND) [RFC3971], IPsec [RFC4301] or TLS [RFC5246] may be necessary. AERO Clients MUST ensure that their connectivity is not used by unauthorized nodes on their EUNs to gain access to a protected network, i.e., AERO Clients that act as routers MUST NOT provide routing services for unauthorized nodes. (This concern is no different than for ordinary hosts that receive an IP address delegation but then "share" the address with unauthorized nodes via some form of Internet connection sharing.) On some AERO links, establishment and maintenance of a direct path between neighbors requires secured coordination such as through the Internet Key Exchange (IKEv2) protocol [RFC5996] to establish a security association. An AERO Client's link-layer address could be rewritten by a link- layer switching element on the path from the Client to the Server and not detected by the DHCPv6 security mechanism. However, such a condition would only be a matter of concern on unmanaged/unsecured links where the link-layer switching elements themselves present a man-in-the-middle attack threat. For this reason, IP security MUST be used when AERO is employed over unmanaged/unsecured links. 7. Acknowledgements Discussions both on IETF lists and in private exchanges helped shape some of the concepts in this work. Individuals who contributed insights include Mikael Abrahamsson, Mark Andrews, Fred Baker, Stewart Bryant, Brian Carpenter, Wojciech Dec, Ralph Droms, Adrian Farrel, Sri Gundavelli, Brian Haberman, Joel Halpern, Tom Herbert, Sascha Hlusiak, Lee Howard, Andre Kostur, Ted Lemon, Andy Malis, Satoru Matsushima, Tomek Mrugalski, Alexandru Petrescu, Behcet Saikaya, Joe Touch, Bernie Volz, Ryuji Wakikawa and Lloyd Wood. Members of the IESG also provided valuable input during their review process that greatly improved the document. Discussions on the v6ops Templin Expires January 28, 2017 [Page 55] Internet-Draft AERO July 2016 list in the December 2015 through January 2016 timeframe further helped clarify AERO multi-addressing capabilities. Special thanks go to Stewart Bryant, Joel Halpern and Brian Haberman for their shepherding guidance during the publication of the AERO first edition. This work has further been encouraged and supported by Boeing colleagues including M. Wayne Benson, Dave Bernhardt, Cam Brodie, Balaguruna Chidambaram, Irene Chin, Bruce Cornish, Claudiu Danilov, Wen Fang, Anthony Gregory, Jeff Holland, Ed King, Gen MacLean, Rob Muszkiewicz, Sean O'Sullivan, Kent Shuey, Brian Skeen, Mike Slane, Brendan Williams, Julie Wulff, Yueli Yang, and other members of the BR&T and BIT mobile networking teams. Wayne Benson is especially acknowledged for his outstanding work in converting the AERO proof- of-concept implementation into production-ready code. Earlier works on NBMA tunneling approaches are found in [RFC2529][RFC5214][RFC5569]. Many of the constructs presented in this second edition of AERO are based on the author's earlier works, including: o The Internet Routing Overlay Network (IRON) [RFC6179][I-D.templin-ironbis] o Virtual Enterprise Traversal (VET) [RFC5558][I-D.templin-intarea-vet] o The Subnetwork Encapsulation and Adaptation Layer (SEAL) [RFC5320][I-D.templin-intarea-seal] o AERO, First Edition [RFC6706] Note that these works cite numerous earlier efforts that are not also cited here due to space limitations. The authors of those earlier works are acknowledged for their insights. 8. References 8.1. Normative References [RFC0768] Postel, J., "User Datagram Protocol", STD 6, RFC 768, DOI 10.17487/RFC0768, August 1980, . [RFC0791] Postel, J., "Internet Protocol", STD 5, RFC 791, DOI 10.17487/RFC0791, September 1981, . Templin Expires January 28, 2017 [Page 56] Internet-Draft AERO July 2016 [RFC0792] Postel, J., "Internet Control Message Protocol", STD 5, RFC 792, DOI 10.17487/RFC0792, September 1981, . [RFC2003] Perkins, C., "IP Encapsulation within IP", RFC 2003, DOI 10.17487/RFC2003, October 1996, . [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, March 1997, . [RFC2460] Deering, S. and R. Hinden, "Internet Protocol, Version 6 (IPv6) Specification", RFC 2460, DOI 10.17487/RFC2460, December 1998, . [RFC2473] Conta, A. and S. Deering, "Generic Packet Tunneling in IPv6 Specification", RFC 2473, DOI 10.17487/RFC2473, December 1998, . [RFC2474] Nichols, K., Blake, S., Baker, F., and D. Black, "Definition of the Differentiated Services Field (DS Field) in the IPv4 and IPv6 Headers", RFC 2474, DOI 10.17487/RFC2474, December 1998, . [RFC3315] Droms, R., Ed., Bound, J., Volz, B., Lemon, T., Perkins, C., and M. Carney, "Dynamic Host Configuration Protocol for IPv6 (DHCPv6)", RFC 3315, DOI 10.17487/RFC3315, July 2003, . [RFC3633] Troan, O. and R. Droms, "IPv6 Prefix Options for Dynamic Host Configuration Protocol (DHCP) version 6", RFC 3633, DOI 10.17487/RFC3633, December 2003, . [RFC3971] Arkko, J., Ed., Kempf, J., Zill, B., and P. Nikander, "SEcure Neighbor Discovery (SEND)", RFC 3971, DOI 10.17487/RFC3971, March 2005, . [RFC4213] Nordmark, E. and R. Gilligan, "Basic Transition Mechanisms for IPv6 Hosts and Routers", RFC 4213, DOI 10.17487/RFC4213, October 2005, . Templin Expires January 28, 2017 [Page 57] Internet-Draft AERO July 2016 [RFC4861] Narten, T., Nordmark, E., Simpson, W., and H. Soliman, "Neighbor Discovery for IP version 6 (IPv6)", RFC 4861, DOI 10.17487/RFC4861, September 2007, . [RFC4862] Thomson, S., Narten, T., and T. Jinmei, "IPv6 Stateless Address Autoconfiguration", RFC 4862, DOI 10.17487/RFC4862, September 2007, . [RFC6434] Jankiewicz, E., Loughney, J., and T. Narten, "IPv6 Node Requirements", RFC 6434, DOI 10.17487/RFC6434, December 2011, . 8.2. Informative References [I-D.herbert-gue-fragmentation] Herbert, T. and F. Templin, "Fragmentation option for Generic UDP Encapsulation", draft-herbert-gue- fragmentation-02 (work in progress), October 2015. [I-D.ietf-dhc-sedhcpv6] Jiang, S., Li, L., Cui, Y., Jinmei, T., Lemon, T., and D. Zhang, "Secure DHCPv6", draft-ietf-dhc-sedhcpv6-13 (work in progress), July 2016. [I-D.ietf-intarea-tunnels] Touch, D. and W. Townsley, "IP Tunnels in the Internet Architecture", draft-ietf-intarea-tunnels-03 (work in progress), July 2016. [I-D.ietf-nvo3-gue] Herbert, T., Yong, L., and O. Zia, "Generic UDP Encapsulation", draft-ietf-nvo3-gue-04 (work in progress), July 2016. [I-D.templin-intarea-grefrag] Templin, F., "GRE Tunnel Fragmentation", draft-templin- intarea-grefrag-02 (work in progress), January 2016. [I-D.templin-intarea-seal] Templin, F., "The Subnetwork Encapsulation and Adaptation Layer (SEAL)", draft-templin-intarea-seal-68 (work in progress), January 2014. [I-D.templin-intarea-vet] Templin, F., "Virtual Enterprise Traversal (VET)", draft- templin-intarea-vet-40 (work in progress), May 2013. Templin Expires January 28, 2017 [Page 58] Internet-Draft AERO July 2016 [I-D.templin-ironbis] Templin, F., "The Interior Routing Overlay Network (IRON)", draft-templin-ironbis-16 (work in progress), March 2014. [RFC0879] Postel, J., "The TCP Maximum Segment Size and Related Topics", RFC 879, DOI 10.17487/RFC0879, November 1983, . [RFC1035] Mockapetris, P., "Domain names - implementation and specification", STD 13, RFC 1035, DOI 10.17487/RFC1035, November 1987, . [RFC1122] Braden, R., Ed., "Requirements for Internet Hosts - Communication Layers", STD 3, RFC 1122, DOI 10.17487/RFC1122, October 1989, . [RFC1191] Mogul, J. and S. Deering, "Path MTU discovery", RFC 1191, DOI 10.17487/RFC1191, November 1990, . [RFC1812] Baker, F., Ed., "Requirements for IP Version 4 Routers", RFC 1812, DOI 10.17487/RFC1812, June 1995, . [RFC1930] Hawkinson, J. and T. Bates, "Guidelines for creation, selection, and registration of an Autonomous System (AS)", BCP 6, RFC 1930, DOI 10.17487/RFC1930, March 1996, . [RFC1981] McCann, J., Deering, S., and J. Mogul, "Path MTU Discovery for IP version 6", RFC 1981, DOI 10.17487/RFC1981, August 1996, . [RFC2131] Droms, R., "Dynamic Host Configuration Protocol", RFC 2131, DOI 10.17487/RFC2131, March 1997, . [RFC2529] Carpenter, B. and C. Jung, "Transmission of IPv6 over IPv4 Domains without Explicit Tunnels", RFC 2529, DOI 10.17487/RFC2529, March 1999, . [RFC2675] Borman, D., Deering, S., and R. Hinden, "IPv6 Jumbograms", RFC 2675, DOI 10.17487/RFC2675, August 1999, . Templin Expires January 28, 2017 [Page 59] Internet-Draft AERO July 2016 [RFC2764] Gleeson, B., Lin, A., Heinanen, J., Armitage, G., and A. Malis, "A Framework for IP Based Virtual Private Networks", RFC 2764, DOI 10.17487/RFC2764, February 2000, . [RFC2784] Farinacci, D., Li, T., Hanks, S., Meyer, D., and P. Traina, "Generic Routing Encapsulation (GRE)", RFC 2784, DOI 10.17487/RFC2784, March 2000, . [RFC2890] Dommety, G., "Key and Sequence Number Extensions to GRE", RFC 2890, DOI 10.17487/RFC2890, September 2000, . [RFC2923] Lahey, K., "TCP Problems with Path MTU Discovery", RFC 2923, DOI 10.17487/RFC2923, September 2000, . [RFC2983] Black, D., "Differentiated Services and Tunnels", RFC 2983, DOI 10.17487/RFC2983, October 2000, . [RFC3168] Ramakrishnan, K., Floyd, S., and D. Black, "The Addition of Explicit Congestion Notification (ECN) to IP", RFC 3168, DOI 10.17487/RFC3168, September 2001, . [RFC3596] Thomson, S., Huitema, C., Ksinant, V., and M. Souissi, "DNS Extensions to Support IP Version 6", RFC 3596, DOI 10.17487/RFC3596, October 2003, . [RFC3819] Karn, P., Ed., Bormann, C., Fairhurst, G., Grossman, D., Ludwig, R., Mahdavi, J., Montenegro, G., Touch, J., and L. Wood, "Advice for Internet Subnetwork Designers", BCP 89, RFC 3819, DOI 10.17487/RFC3819, July 2004, . [RFC4271] Rekhter, Y., Ed., Li, T., Ed., and S. Hares, Ed., "A Border Gateway Protocol 4 (BGP-4)", RFC 4271, DOI 10.17487/RFC4271, January 2006, . [RFC4291] Hinden, R. and S. Deering, "IP Version 6 Addressing Architecture", RFC 4291, DOI 10.17487/RFC4291, February 2006, . Templin Expires January 28, 2017 [Page 60] Internet-Draft AERO July 2016 [RFC4301] Kent, S. and K. Seo, "Security Architecture for the Internet Protocol", RFC 4301, DOI 10.17487/RFC4301, December 2005, . [RFC4443] Conta, A., Deering, S., and M. Gupta, Ed., "Internet Control Message Protocol (ICMPv6) for the Internet Protocol Version 6 (IPv6) Specification", RFC 4443, DOI 10.17487/RFC4443, March 2006, . [RFC4459] Savola, P., "MTU and Fragmentation Issues with In-the- Network Tunneling", RFC 4459, DOI 10.17487/RFC4459, April 2006, . [RFC4511] Sermersheim, J., Ed., "Lightweight Directory Access Protocol (LDAP): The Protocol", RFC 4511, DOI 10.17487/RFC4511, June 2006, . [RFC4555] Eronen, P., "IKEv2 Mobility and Multihoming Protocol (MOBIKE)", RFC 4555, DOI 10.17487/RFC4555, June 2006, . [RFC4592] Lewis, E., "The Role of Wildcards in the Domain Name System", RFC 4592, DOI 10.17487/RFC4592, July 2006, . [RFC4605] Fenner, B., He, H., Haberman, B., and H. Sandick, "Internet Group Management Protocol (IGMP) / Multicast Listener Discovery (MLD)-Based Multicast Forwarding ("IGMP/MLD Proxying")", RFC 4605, DOI 10.17487/RFC4605, August 2006, . [RFC4821] Mathis, M. and J. Heffner, "Packetization Layer Path MTU Discovery", RFC 4821, DOI 10.17487/RFC4821, March 2007, . [RFC4963] Heffner, J., Mathis, M., and B. Chandler, "IPv4 Reassembly Errors at High Data Rates", RFC 4963, DOI 10.17487/RFC4963, July 2007, . [RFC4994] Zeng, S., Volz, B., Kinnear, K., and J. Brzozowski, "DHCPv6 Relay Agent Echo Request Option", RFC 4994, DOI 10.17487/RFC4994, September 2007, . Templin Expires January 28, 2017 [Page 61] Internet-Draft AERO July 2016 [RFC5213] Gundavelli, S., Ed., Leung, K., Devarapalli, V., Chowdhury, K., and B. Patil, "Proxy Mobile IPv6", RFC 5213, DOI 10.17487/RFC5213, August 2008, . [RFC5214] Templin, F., Gleeson, T., and D. Thaler, "Intra-Site Automatic Tunnel Addressing Protocol (ISATAP)", RFC 5214, DOI 10.17487/RFC5214, March 2008, . [RFC5246] Dierks, T. and E. Rescorla, "The Transport Layer Security (TLS) Protocol Version 1.2", RFC 5246, DOI 10.17487/RFC5246, August 2008, . [RFC5320] Templin, F., Ed., "The Subnetwork Encapsulation and Adaptation Layer (SEAL)", RFC 5320, DOI 10.17487/RFC5320, February 2010, . [RFC5494] Arkko, J. and C. Pignataro, "IANA Allocation Guidelines for the Address Resolution Protocol (ARP)", RFC 5494, DOI 10.17487/RFC5494, April 2009, . [RFC5522] Eddy, W., Ivancic, W., and T. Davis, "Network Mobility Route Optimization Requirements for Operational Use in Aeronautics and Space Exploration Mobile Networks", RFC 5522, DOI 10.17487/RFC5522, October 2009, . [RFC5558] Templin, F., Ed., "Virtual Enterprise Traversal (VET)", RFC 5558, DOI 10.17487/RFC5558, February 2010, . [RFC5569] Despres, R., "IPv6 Rapid Deployment on IPv4 Infrastructures (6rd)", RFC 5569, DOI 10.17487/RFC5569, January 2010, . [RFC5720] Templin, F., "Routing and Addressing in Networks with Global Enterprise Recursion (RANGER)", RFC 5720, DOI 10.17487/RFC5720, February 2010, . [RFC5844] Wakikawa, R. and S. Gundavelli, "IPv4 Support for Proxy Mobile IPv6", RFC 5844, DOI 10.17487/RFC5844, May 2010, . Templin Expires January 28, 2017 [Page 62] Internet-Draft AERO July 2016 [RFC5949] Yokota, H., Chowdhury, K., Koodli, R., Patil, B., and F. Xia, "Fast Handovers for Proxy Mobile IPv6", RFC 5949, DOI 10.17487/RFC5949, September 2010, . [RFC5996] Kaufman, C., Hoffman, P., Nir, Y., and P. Eronen, "Internet Key Exchange Protocol Version 2 (IKEv2)", RFC 5996, DOI 10.17487/RFC5996, September 2010, . [RFC6146] Bagnulo, M., Matthews, P., and I. van Beijnum, "Stateful NAT64: Network Address and Protocol Translation from IPv6 Clients to IPv4 Servers", RFC 6146, DOI 10.17487/RFC6146, April 2011, . [RFC6179] Templin, F., Ed., "The Internet Routing Overlay Network (IRON)", RFC 6179, DOI 10.17487/RFC6179, March 2011, . [RFC6204] Singh, H., Beebee, W., Donley, C., Stark, B., and O. Troan, Ed., "Basic Requirements for IPv6 Customer Edge Routers", RFC 6204, DOI 10.17487/RFC6204, April 2011, . [RFC6221] Miles, D., Ed., Ooghe, S., Dec, W., Krishnan, S., and A. Kavanagh, "Lightweight DHCPv6 Relay Agent", RFC 6221, DOI 10.17487/RFC6221, May 2011, . [RFC6241] Enns, R., Ed., Bjorklund, M., Ed., Schoenwaelder, J., Ed., and A. Bierman, Ed., "Network Configuration Protocol (NETCONF)", RFC 6241, DOI 10.17487/RFC6241, June 2011, . [RFC6275] Perkins, C., Ed., Johnson, D., and J. Arkko, "Mobility Support in IPv6", RFC 6275, DOI 10.17487/RFC6275, July 2011, . [RFC6355] Narten, T. and J. Johnson, "Definition of the UUID-Based DHCPv6 Unique Identifier (DUID-UUID)", RFC 6355, DOI 10.17487/RFC6355, August 2011, . [RFC6422] Lemon, T. and Q. Wu, "Relay-Supplied DHCP Options", RFC 6422, DOI 10.17487/RFC6422, December 2011, . Templin Expires January 28, 2017 [Page 63] Internet-Draft AERO July 2016 [RFC6438] Carpenter, B. and S. Amante, "Using the IPv6 Flow Label for Equal Cost Multipath Routing and Link Aggregation in Tunnels", RFC 6438, DOI 10.17487/RFC6438, November 2011, . [RFC6691] Borman, D., "TCP Options and Maximum Segment Size (MSS)", RFC 6691, DOI 10.17487/RFC6691, July 2012, . [RFC6706] Templin, F., Ed., "Asymmetric Extended Route Optimization (AERO)", RFC 6706, DOI 10.17487/RFC6706, August 2012, . [RFC6864] Touch, J., "Updated Specification of the IPv4 ID Field", RFC 6864, DOI 10.17487/RFC6864, February 2013, . [RFC6935] Eubanks, M., Chimento, P., and M. Westerlund, "IPv6 and UDP Checksums for Tunneled Packets", RFC 6935, DOI 10.17487/RFC6935, April 2013, . [RFC6936] Fairhurst, G. and M. Westerlund, "Applicability Statement for the Use of IPv6 UDP Datagrams with Zero Checksums", RFC 6936, DOI 10.17487/RFC6936, April 2013, . [RFC6939] Halwasia, G., Bhandari, S., and W. Dec, "Client Link-Layer Address Option in DHCPv6", RFC 6939, DOI 10.17487/RFC6939, May 2013, . [RFC6980] Gont, F., "Security Implications of IPv6 Fragmentation with IPv6 Neighbor Discovery", RFC 6980, DOI 10.17487/RFC6980, August 2013, . [RFC7078] Matsumoto, A., Fujisaki, T., and T. Chown, "Distributing Address Selection Policy Using DHCPv6", RFC 7078, DOI 10.17487/RFC7078, January 2014, . [TUNTAP] Wikipedia, W., "http://en.wikipedia.org/wiki/TUN/TAP", October 2014. Templin Expires January 28, 2017 [Page 64] Internet-Draft AERO July 2016 Appendix A. AERO Alternate Encapsulations When GUE encapsulation is not needed, AERO can use common encapsulations such as IP-in-IP [RFC2003][RFC2473][RFC4213], Generic Routing Encapsulation (GRE) [RFC2784][RFC2890] and others. The encapsulation is therefore only differentiated from non-AERO tunnels through the application of AERO control messaging and not through, e.g., a well-known UDP port number. As for GUE encapsulation, alternate AERO encapsulation formats may require encapsulation layer fragmentation. For simple IP-in-IP encapsulation, an IPv6 fragment header is inserted directly between the inner and outer IP headers when needed, i.e., even if the outer header is IPv4. The IPv6 Fragment Header is identified to the outer IP layer by its IP protocol number, and the Next Header field in the IPv6 Fragment Header identifies the inner IP header version. For GRE encapsulation, a GRE fragment header is inserted within the GRE header [I-D.templin-intarea-grefrag]. Figure 9 shows the AERO IP-in-IP encapsulation format before any fragmentation is applied: +-+-+-+-+-+-+-+-+-+-+-+-+-+-+ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Outer IPv4 Header | | Outer IPv6 Header | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |IPv6 Frag Header (optional)| |IPv6 Frag Header (optional)| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Inner IP Header | | Inner IP Header | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | | | ~ ~ ~ ~ ~ Inner Packet Body ~ ~ Inner Packet Body ~ ~ ~ ~ ~ | | | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Minimal Encapsulation in IPv4 Minimal Encapsulation in IPv6 Figure 9: Minimal Encapsulation Format using IP-in-IP Figure 10 shows the AERO GRE encapsulation format before any fragmentation is applied: Templin Expires January 28, 2017 [Page 65] Internet-Draft AERO July 2016 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Outer IP Header | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | GRE Header | | (with checksum, key, etc..) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | GRE Fragment Header (optional)| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Inner IP Header | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | ~ ~ ~ Inner Packet Body ~ ~ ~ | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 10: Minimal Encapsulation Using GRE Alternate encapsulation may be preferred in environments where GUE encapsulation would add unnecessary overhead. For example, certain low-bandwidth wireless data links may benefit from a reduced encapsulation overhead. GUE encapsulation can traverse network paths that are inaccessible to non-UDP encapsulations, e.g., for crossing Network Address Translators (NATs). More and more, network middleboxes are also being configured to discard packets that include anything other than a well-known IP protocol such as UDP and TCP. It may therefore be necessary to determine the potential for middlebox filtering before enabling alternate encapsulation in a given environment. In addition to IP-in-IP, GRE and GUE, AERO can also use security encapsulations such as IPsec and SSL/TLS. In that case, AERO control messaging and route determination occur before security encapsulation is applied for outgoing packets and after security decapsulation is applied for incoming packets. Appendix B. When to Insert an Encapsulation Fragment Header An encapsulation fragment header is inserted when the AERO tunnel ingress needs to apply fragmentation to accommodate packets that must be delivered without loss due to a size restriction. Fragmentation is performed on the inner packet while encapsulating each inner packet fragment in outer IP and encapsulation layer headers that differ only in the fragment header fields. Templin Expires January 28, 2017 [Page 66] Internet-Draft AERO July 2016 The fragment header can also be inserted in order to include a coherent Identification value with each packet, e.g., to aid in Duplicate Packet Detection (DPD). In this way, network nodes can cache the Identification values of recently-seen packets and use the cached values to determine whether a newly-arrived packet is in fact a duplicate. The Identification value within each packet could further provide a rough indicator of packet reordering, e.g., in cases when the tunnel egress wishes to discard packets that are grossly out of order. In some use cases, there may be operational assurance that no fragmentation of any kind will be necessary, or that only occasional large control messages will require fragmentation. In that case, the encapsulation fragment header can be omitted and ordinary fragmentation of the outer IP protocol version can be applied when necessary. Author's Address Fred L. Templin (editor) Boeing Research & Technology P.O. Box 3707 Seattle, WA 98124 USA Email: fltemplin@acm.org Templin Expires January 28, 2017 [Page 67]